Doc I'm using wdww With felix lube. Have had a lot of luck with this combo in the 223 with other boolits.
Doc I'm using wdww With felix lube. Have had a lot of luck with this combo in the 223 with other boolits.
357,
What is the OD on the bottom band of these bullets from WW's ??
IHMSA # 566 "time sure flies when you're having FUN"
I shoot my original Eagan 62 in 1-12" Savage 22-250 barrels down to 1900 with fine accuracy.I have shot a few groups under 1/2" with it and many under 1" even in a Stevens 200 Sporter.I have never used it in any other guns except my 1-12 Savages.I have given samples to others who have used them in 1-9's with good luck though.In the CBA Fouling Shot magazine a couple years back i had a barely readable article on shooting my Stevens 200 22-250 with cast and all of the load data.I cant seem to find the file on m computer otherwise i would post it.
George
Last edited by HARRYMPOPE; 07-10-2012 at 11:39 PM.
Damn, how is yours casting almost .001 bigger that mine?? My first casting was out of my "lino" pot, I'm getting .2245-.225 on the bottom band and .2235-.224 on the second. I'll check and TL and try these in my 14" 222 bbl. and load to 1900 fps.and see what that brings
IHMSA # 566 "time sure flies when you're having FUN"
Tried them in my 14 twist 223 this afternoon and it is a no go. It would group a few and then one would yaw and hit at random. Running Tac #1, 15 gr 4895, sized .225, wolf SRM primer, WDWW. I might try some more 4895 in the case but my testing with this barrel showed accuracy went to pot with the NOE 22-55 after 16 gr or so.
Thinking about pulling the Ruger MK II target out of the safe for another go round with cast. I haven't had much luck with it but this boolit shows promise and the 12 twist should be just the ticket.
I finally got a chance to try out the new mold and shoot some boolits. Not much info. on the 62gr bullet in the manuals I have so I used the 55gr min. & went up from there. I tried a Savage Axis in 22-250 w/a 1-12 twist first. Started w/IMR 4759, WLR primers, Randy's Tac#1 lube sized to .224, only lubed the first groove & gas ck, seated the boolet so the base is right at the neck & shoulder junction. Stepped out the back door and fired some rounds. I started @ about 20yds cause I just wanted to see if I'd get any leading. I have no idea on the alloy, only that it's a 14bhn according to my eyes and the Lee tester. It's a mix of ww, & 60/40, I started with ww and added the 60/40 until I started getting well filled out boolits. Temp was 700-725 according to my RCBS thermometer. They dropped @ .225 on the bottom band, cks just snapped right into place.
Only so, so results w/the 22-250, sideways boolits on a few. Didn't adjust the scope at all from where it was zero'd w/jacketed, just picked a spot & squeezed. Eash is a 3 shot group. There was no leading and a lube star at the muzzle w/each charge wt. May have to experiment w/powders to find the right node.
Tried the same boolit in the .223 w/a 1-9..much better results.
Unique....8.5
RX7......11.5
IMR 4759....in the 9, 10, 10.5
All 3 shot groups, I had to look twice but it's there.
Next is to try them at 50, then out to 100. I'm pretty happy w/the .223 so far. One day I'll get a battery for the chrono & see how fast they're going.
Good to know they work ok in a 1/9 as it was the slowest twist I could get a good deal on when I bought the barrel for my AR build.
"If people let the government decide what foods they eat and what medicines they take, their bodies will soon be in as sorry a state as are the souls of those who live under tyranny."
-Thomas Jefferson
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |