Re Re Re... Rerun of Miha 9mm 125gn HP mold

[Dannix]

Update from Miha: I just ordered pins. So yes it will be in production soon. (March28-2012)
Update2: This GB is now CLOSED

Rerun of Miha 9mm 125gn HP mold.

• Brass
• Hollowpoint (or Solid!)
• ~125gr HP / ~130gr Solid
• 4 Cavity

Official Pricing
Hollowpoint: $120 + $20 shipping, +$16 for extra pins
Solid: $90 + $15 shipping


Note: No mixing of GC and PB in the same mould
Is this good for .357 Sig? Likely No.

Pretty self explanatory. Miha emails paypal payment requests direct to customers, so a honcho is not needed for this GB. This GB will be closed once Miha has posted requesting its closure.


When signing up, please specify:

• Plain Based or Gas Check
• HP or Solid
• Round Pins Only (i.e. No extra pin charge), Round + Penta, Round + Penta + Solid (for making solids in the HP Moulds without the Penta or Round points poking out the bottom), Penta + Solid, Round + Solid ... you get the idea.
• Desired diameter
• Your email address (obfuscated to avoid spambots)

Defaults, if not specified:

• Plain Based
• HP
• Round Pins Only
• .359 Diameter

Side note: Tips on using this mould

Please post your favorite loads once this GB is complete, and you've found one you like:
The Recommended Load thead for the Miha 9mm 125gn HP mold

[Dannix]

Last Update: Aprl 14, 2012

1. chprplt - 4 cav solid, ? diameter
2. chprplt - 4 cav HP, both types of pins + blank pins, ? diameter
3. GMT210 - 4cav, solid (not HP), .357, mabennett at neo.rr.com
I am #3 on this group buy. I changed from a solid 357-125 4 cavity to a 357-125 4 cavity cramer with round and solid pins, I confirmed the change with MiHec.

4. Dannix - 4cav, HP, PB, round pins and pins for solids + an extra set of round pins, .359 diameter, dpumpkin [@+] runbox (d0+) com + 1 set of handles
6. CPL Lou - 4 cavity, round and penta pins, .359" diameter, GC base (if GasCheck possible). louiestanfield (at) gmail (dot) com.
7. Greg in va - 4 cav, plain and HP pins, .359 size, gdedavis at aol dot com
8. Dirtdgger - 4cavity hp pb round pins 359 dirtdgger3355atyahoodotcom
9. DocHoliday - 4 Cav, HP, PB, All Pins, .359 Diameter, Bhouseholder84 at yahoo dot com

12. frugal - 4 cav HP, both types of pins, .359" diameter, n5035615 (at) yahoo (dot) com + 1 set of handles
13. denul - 4 cav HP, both types of pins, .358" diameter, dennis.a.ulrich -at- gmail -dot- com
17. ph4570 - 4 cav, Plain Based HP, Round + Penta + Solid pins, 0.360 diameter, videodog at comcast dot net
18. Christorbust - 4 Cav, HP, PB, Round and Penta pins, .358 Diameter, [email address redacted]

From the SOLID interest thread:
2. rollmyown -1 mold - solid, Plain base, .359" , bert000 at yahoo dot com
3. Mallard57 - 1 mold - solid

19. Wots - 4C, PB, HP, Round+Penta pins, .359 Diameter. WotsamtrU at aol dot com + 2 sets of handles
20. Aaron - 4 cav HP, all types of pins, .359 diameter, 5090shiloh /at/ gmail \dot\ com
21. bld451 - 4 cav HP, both types of pins, .359" diameter, brentsmail at comcast.net AND str8shooter2 at comcast dot net + 1 set of handles
23. Iron Mike Golf - 4 cav HP, both types of pins + blank pins, 358 diameter, sugdenjw /at/ msn \dot\ com
24. badluther - 4 cav, HP, PB, Round + Penta + Solid, .359, st1975 at (yahoo.com)
25. Beerd - 4 cav, PB, HP, Round + Penta + Solid, 0.359, petek[circle a]bresnan(dot)gnet
26. bfuller14 HP 2 or 4 cavity which ever you go with, all pins, .359, GasCheck, bfuller one nine six one@sbcglobal.net
27. jethunter - 4C, HP, plain base, penta + round pins, .357", j3526134 at telus dot net
28. huntnman, 2 or 4 cavity, round pins & blank pins for solids, .359, huntnman {AT} swbell {dot} net
29. OHPrepper7 - 4 Cavity, plain base, HP, both sets of pins, .359 diameter, ers27 (at) zips.uakron.edu
30. shotstring - 4 cavity, plain base, HP, round pins, 358 diameter vickiandbob at frontier dot com
31. Village Idiot - 4 cav, HP, round and solid pins, 359, plain base krzin08 at yahoo dot com
32. quasi - 4cav, HP, plain base, penta + round pins, .359 ckulyk (at) shaw (dot) ca
33. JPinMI - 4 Cav, HP, PB, Round + Penta + Solid, 358 Desired diameter, jphansen1atcharterdotnet + 2 sets of handles
34. rjbishop - 4 Cav, HP, GC Base, All Pins, .359 Diameter, rbish55 _at_ gmail dot com
35. nspctr7 - 4 cav, HP, PB, round , penta, and solid pins, .358 dia, nspctr7 at yahoo dot com
36. Live2Ride - 4 cav HP, round and penta pins, .358" diameter, dan underscore harben at msn dot com
37. shotstring - 4 cav HP, PB, both sets of pins, 358 dia, vickiandbob at frontier dot com
38. Beau Cassidy - 4 cavity, HP, Round pins, 358, Smallmouth. Dot. Catcher. At y- hoo
39. Elkins45 - 4cav, HP, PB, round pins, .359, . Elkins (circle a) iglou (period) com + 1 set of handles
40. leadbutt - 4 cav HP, PB, round pins only, .359, watucker22 at yahoo dot com
41. shangrila - 4 cav, HP, PB, all pins, .359, unluckyone at mailcity dot com
42. Rattlesnake Charlie - 4 cav, PB, Penta, round, and solid pins, .359, charles underscore nuss aaat yahoo doot com
43. Don1955 - 4cav, HP, PB, Round + Penta + Solid, debent55 at frontier dot com

45. sewerman68 - 2 or 4 cavity 358 hp, round & penta pins, finn m 39 at yahoo dot com.
46. Jeff Michel - 4 cavity, HP, penta/round/small pins, .359 diameter, bmsouderatymaildotcom
47. skimmerhead - 4-cav with penta pins .358 ----------- + 1 set of handles
skimmerhead had to bail out. This is being picked up by DRNurse1.DRNurse1's email address: DRNurse1 [at] hotmail /dot/com

48. tcart - 4 Cavity, Plain Based, HP, Round and Penta Pins .359 Diameter. tcart at hotmail dot com
49. Dschuttig - 4 cav, if I can get penta pins instead of round that would be great. But if I have to buy both sets of pins to get the penta then I'll take the round. .360 diam. dschuttig at yahoo dot com
50. scrubber - 4 Cavity, Gas check, HP, All Pins, .359 diameter, dlporter (at) speakeasy (dot) net + 1 set of handles
51. Reload3006 - .359 4 cavity PB penta hp and solid pins. Dcrop77380 at aol dot com
52a. Swedlead - 4 cav , pb, HP, all types pins, .359 dia, jorgen [at] asab [dot] nu (Swedlead would like 2 moulds)
52b. Swedlead - 4 cav , pb, HP, all types pins, .359 dia, jorgen [at] asab [dot] nu (Swedlead would like 2 moulds)
53. h1tdk00 - 4 cav HP PB round and solid pins, 358 dia, tkunz500 (at) att (dot) net
54. Farmerguy - 4 Cavities, Plain Based, HP, All Pins, .359 diameter, waterman64 at frontiernet dot net
55. sig2009 - 4 cavity, solid, plain base, .359, jsenuta at hotmail dot com
56. 40Super - 4cav, PB, HP, Penta + Solid pins,.359 size, march70jeff at frontier dot com
57. MSGO-Hammer - 4Cav PB Solid .359 msgunowners at hotmail dot com + 1 set of handles
58. hotwheelz - 4cav. plain base solid .359 willsfxsts at gmail dot com + 1 set of handles
59. IIJSavoy - 4cav, PB, Round+Penta+Solid pins, .359 Diameter, iijsep at gmail dot com
60. Paulinski - 4 cavity, solid, .359, pkrysztofiak (at) gmail.com
61. scvpiper - 4 Cavity, plain base, HP, both round and penta pins + solid pins, .359, scvpiper at sbcglobal.net
62. head for the hills - 4 cavity, plain based, round pins and solid pins, .358" diameter, c.everly at frontiernet.net + 1 set of handles
63. Bodydoc447 - 4cav, PB, Solid, 0.358", BodyDoc447 AT aol DOT com
64. library - 4 cavity, PB, HP, Round+Penta pins, .359 Diameter, leaberry 'located at' gmail.com
65. BeeMan - 4 cavity, plain base, HP, round + solid pins, .358 diameter sdunn at outdrs dot net
66. Rotaxxx - 4 cavity hp with both set of pins, .358", Rotax599 at hotmail dot com -- presuming penta and round pins
67. HenryC460 - 4 cavity 358, round, penta, and "solid" pins, jhg416400 at yahoo dot com
68. Redwoode - 4 cav HP PB Round + Solid Pins .359 Redwoode [at] yahoo [dot] com + 1 set of handles
69. captaint - 4 cav HP plain base, both sets of pins, .359 diameter roctober5thatgmailedotcom -- presuming penta and round pins + 1 set of handles
70. Beau Cassidy - [4cav] plain base, HP, round pins, .359 dia. smallmouth.catcher>>yah00...c0m
71. Crash Corrigan - 4 Cav PB Penta pin .359 dia crash corrigan at cox dot net
72. MostlyOnThePaper - 4C, PB, HP/ Round+Penta .359 kc5vtk at comcast dot net + 1 set of handles
73. Wilson - 4 cavity, Plain Based , HP , Round Pins Only , .358 Diameter, hickmangroup at gmail dot com
74. vparra559 - 4cav-pb-all pin types .359 diegotali2 at yahoo dot com
75. rick4276 - 4 cavity, .358, pb, all pin types, taylorcra at rochester dot rr dot com
----------------
76. CATS - four cavity, plain base, round, penta and solid pins, .359 dia
77. Dutch4122 - If there are extra's left over on this group buy I would like to grab a 4 cavity with round H/P pins and flat nose plug pins. dutch4122(at)yahoo(dot)com

[Dirtdgger]

I'm still interested in this mold. Hope you can get it going.

[DocHoliday]

I hope this time this one gets off the ground. I am interested in this mould. I would take it as a 2 or 4 cavity. Would like both sets of pins. Either way I am in for one.

[Greg in va]

Yes I still want one....

[CPL Lou]

Thanks Dannix...I'm still in.
4 cavity hollow point mold with both types of pins.
.359" diameter

Hope we get a honcho soon.
I would volunteer, but my health issues negate that possibility.

[el general]

4 cavity hollow point mold with both types of pins.
but i don´t know if i need .359" diameter, .358", or .357" diameter.

[frugal]

I'm in for a 4 cavity mould with both types of pins.
.359" diameter

[DocHoliday]

That makes 7 only 8 more to go. Come on you know yall want one.

[denul]

put me down,.358,4 cavity,pb,all pins.

[Idaho Sharpshooter]

Ok, stick me on the list.

4-cavity, all HP, plainbase, .358" is close enough.

Rich

[GMT210]

I'd still be interested if it was available as a solid mold, I'm not interested in another HP mold.

GMT

[Dannix]

I'd still be interested if it was available as a solid mold, I'm not interested in another HP mold.

GMT

I would think that would be doable. Putting you on the list. Miha should be able to clarify if this will be available as a solid once this goes active.

[Dannix]

I'd still be interested if it was available as a solid mold, I'm not interested in another HP mold.

GMT

Based on this link, we can run solids in addition to HPs.

So yes, should be available as a solid mold no problem. We'll wait until this becomes active before specifying who wants precisely what though. We'll keep it simply with just a name listing for now.

[GMT210]

Dannix,

You've got me listed twice in your interest list.

GMT210

[Roger Ronas]

Interested at this point. Will reconfirm when I see schedule and price.
4 cavity hollow point mold with both types of pins.
.359" diameter

Roger

[chprplt]

I'm number 3 on the list. I'm definitely still interested. Put me down for one four cavity hollow point mould with whatever pins are available and well as blank pins and one four cavity solid mould. I'll get back with you on the diameter. thank you.

[ph4570]

I will likely go for a 4 cav HP. Can it be had at 0.360? Expected cost and schedule?

[Dannix]

List updated.

I will likely go for a 4 cav HP. Can it be had at 0.360? Expected cost and schedule?

Sorry, not sure sure on cost nor schedule. I'd imagine Miha could do .360 no problem.

[Christorbust]

We'll wait until this becomes active before specifying who wants precisely what though. We'll keep it simply with just a name listing for now.

In the interest of simplicity, I'm simply interested in a 4 cav HP.