Sharp as needle..High BC:s, but would it be possible to have them for the .338:s..
If there is enough interested people, maybe Swede will press the go- button for it.
S
Hope this photo works.
Sharp as needle..High BC:s, but would it be possible to have them for the .338:s..
If there is enough interested people, maybe Swede will press the go- button for it.
S
Hope this photo works.
Last edited by seppos; 03-06-2011 at 04:22 AM.
Am I the only one having trouble opening the link to Photobucket? Seppos - You thinking something in the 250-260 grain range? If Swede would do something like he did for the 358318 RNGC GB where you could get one cavity HP'd and the HP pin puts a flat point or a HP on the boolet, Hmmmm..... very interesting.
JK
Last edited by Trapaddict; 03-18-2011 at 11:42 AM.
A woman has the last word in any argument.
Anything a man says after that is the beginning of a new argument.
Couldn`t get photobucket to open either. The idea of the mold is interesting though.Robert
Surprised there isn't more interest in this one. Nice practice/plinker for the 338 Edge and Lapuas.
Bump to the top.
Jeff
A woman has the last word in any argument.
Anything a man says after that is the beginning of a new argument.
I´m interested! Need such a mold for my 338Lapua.
Back up on top.
This one must be of interest to more people!...?
250-300grainer would be fine. Byt i'd like the boolit as pointy as possible...maybe a 300grainer would need a blunt nose to be short enough to fred through My rifles magazine. I'd probably use it as singleshot repeater anyhow...hmm
Sent from my iPhone using Tapatalk
Please check out my youtubechannel "fullfartiskogen" !
I'd even entertain the idea of a boolit heavier than 300 grains We might be giving-up some velocity anyway, to keep the leading controlled, longer boolit means higher BC (all else being equal, of course)
Maybe a sharp point and 325-to-350 grains?
I'd be in for a 300 grain (or so) sharp.....
I'd like to have one also, sharp point at least 250 gr.
Frank
Last edited by frnkeore; 09-03-2011 at 02:11 AM.
Bump for interest....;- )
I would be interested.
Aaron
339365 in a 300gr would be just fine. Pencil me in if y'all would.
Rich
OK, I'm firmly commited to a 2-or-3 cavity of the "340302". And I'd pop the extra $10 for the small order, if required.
Ok, i'll bite.
A 3 or 4 holer +$10 is fine with me if the boreriding part is snug enough for my barrel...need to slug it.
---
I am here: http://maps.google.com/maps?ll=59.065212,15.348860
Sent from my iPhone using Tapatalk
Please check out my youtubechannel "fullfartiskogen" !
I'm ok with an extra $10..... Count me in!
I would like a 4-cavity.
SCB were you thinking of any particular cartridge with this in mind..? Seems the .338 Spectre would benefit from it, especially if its basically a scaled up and sharpened up 311247...
A flatnose pin or some easy way to flatten would be nice, but considering the cost of .338 j-words, anything is an improvement
I'm definitely interested.
SC
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |