THIS BUY IS CLOSED, ORDER IS IN WITH NOE.
This mould will be offered by NOE as a clone of the Lee 430-310-RF. However, it will be available as either a gas check or plain base, with the usual 1-5 cavity, HP, and RG2 and 4 options, and dropping at about .434 from the mould. Below are the drawings of the GC, PB and HP designs.
I will be the honcho of this buy and will accept mailed payments and payments via PayPal (+$4.50 per mould). Please post here what you want and I will update the list regularly. The buy will stay open until Swede Nelson tells me to make the last call before it goes to production.
We are now on the production schedule, currently listed for June 2011. I will start accepting payments now, but payment will not be required until we get closer to production. Assuming we stay on the schedule for June I will send out a PM for payment to those who haven't paid on or about June 1st. PM me for payment information when you want to pay before that.
Buyers list:
PM has been sent for payment to those who have not already paid. Thanks!
*1) Landric 3 Cavity 1GC 2PB
*2) Landric RG2 1GC 1PB
*3) Happy 7 RG4 4PB -DRILL FOR PROBE
*4) Happy 7 5 Cavity 5PB -DRILL FOR PROBE
*5) GLL 1 Cavity 1GC-HP & 3 extra blank pins -DRILL FOR PROBE
*6) GLL 4 Cavity 2GC 2PB -DRILL FOR PROBE
*7) jj850 RG4 4GC
*8) GL49 RG4 4GC
*9) Wired54 5 Cavity 5PB
*10) bburnz RG4 4GC
*11) DaveD RG2 2GC
*12) dominicfortune00 4 Cavity 4PB
*13) Heavy lead 5 Cavity 5GC
*14) jschmuck 4 Cavity 4PB
*15) johnch RG2 2GC
*16) AnthonyB RG2 2GC w/ Extra Pin Set
*17) jkingrph 2 Cavity 1GC 1PB
*18) nicholst55 2GC 2PB
*19) happietoshoot 5 Cavity 5PB
*20) Drb RG4 4GC
Moulds will be machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.
The cost will be as follows:
Aluminum Moulds-
Standard Molds
Single cavity mould $68.00 Ea.
Double cavity mould $72.00 Ea.
Three cavity mould $79.00 Ea.
Four cavity mould $85.00 Ea.
Five cavity mould $92.00 Ea.
Hollow pointing one cavity and furnishing a double ended pin would be $35.00 extra.
If you want to fashion different HP profiles, an extra blank pin would be $1.50
RG Molds
Two cavity RG2 HP mould $96.00 Ea.
Includes one set of hollow point pins
and one set of flat nose pins.
If you want to fashion different HP profiles for the RG2 an extra blank pin set of two (2) would be $4.
Four cavity RG4 HP mould $126.00 Ea.
Includes one set of hollow point pins
and one set of flat nose pins.
If you want to fashion different HP profiles for the RG4 an extra blank pin set of four (4) would be $8.
Shipping and handling will be $10 per order (1 or 2 moulds) and shipped priority mail. If you live outside the United States contact me, and I will work with you, shipping should be $20 for 1 or 2 moulds.