Looks like an old axle nut of the older F-15A&B's or another fighter aircraft.
Type: Posts; User: HardColt
Forum: Our Town
Looks like an old axle nut of the older F-15A&B's or another fighter aircraft.
Forum: Our Town
Bought some CCI from Academy Sport for 7.99 per 100, bought 10 boxes and even delivered it to my Virginia address. Its all gone now except for store pickup. Academy don't gouge their customers....
Forum: Completed Deals
I hate those sml primer pocket 45 ACP brass. Especially all my stashed primers are lrg.primers.
Forum: Gunsmithing Tips & Tricks
What he used? A Weller soldering iron? Poor SKS.
Forum: Cast Boolits
Thank you very much for taking the time to go into such great depth explaining ballistics,atmospheric variances etc. It is just a matter of how you plan to push that bullet into what speeds you want...
Forum: Cast Boolits
Thanks for all the input. I was planning to cast the 160 grain for the 300BO powdercoated but will bear in mind what powder to load behind the bullet.
Forum: Our Town
I'll pray for you for a quick recovery. Good the VA got you covered. My VA in Virginia was good to me too with my back problems.
Forum: Cast Boolits
Hello to everyone! Just been reading a lot regarding 300 Blackout but have not come across any information on how cast bullet weights are categorized as being supersonic or subsonic. I have a Lee 312...
Forum: Cast Boolits
60 yrs. old next month. Thankful to God for feeling young, except trying to get out of bed in the morning and feeling my back and right knee creaking on me. I could use some ballistol to lube it ....
Forum: Reloading Equipment
Thanks. Did advice my cousin to use aluminum tape and just use the 9mm diameter base to punch the holes for it. I recall even using the collator for the 45 ACP's some of the cases end up wrong side...
Forum: Reloading Equipment
Thanks for the reply. I never drilled mine but I will do that when I have a chance. The tubes are replaced by smaller tubes if I remember or maybe not. Is there are smaller tube sets for the case...
Forum: Reloading Equipment
I just can't remember if the collator needs to be change with the appropriate tubes to fit the case feeder. I'm trying to help my cousin on what to get from FS or Titan. I used to reload on my...
Forum: Reloading Equipment
Hello! Been so many years gone by and can't remember if there is such a thing as a small case collator for a Pro1000? If you plan to load .380 or 9mm or does the small case tubes adapt to it? I can...
Forum: Coatings and Alternatives
My indoor range in Virginia used to let members shoot lead bullets, then several years back they prohibited the used of lead bullets with the exception of the .22 LR hollow points. I think they were...
Forum: Reloading Equipment
I've used Tula and Wolf brands when the price and availability of CCI's went up. I never had problems with them but majority of the my reloads I prime using the Lee hand prime. My experience is very...
I can't remember which way the sprue bolts loosen or tighten but I have installed conical washer and tighten them before and with just the right torque the washer tighten the bolt sufficiently so it...
If you're low on your lead stash! I highly recommend THE CAPTAIN. Prompt delivery, helpful, good follow through from start to finish. Nothing else can go wrong when dealing with her. Thank you & God...
Forum: Cookin' Recipe's
Sir:
Your chicken pictures make me hungry! Too bad I can't pinch the pictures to taste.
Forum: Reloading Equipment
Since the price of CCI primers have considerably risen for a couple of years, I switched to Wolf and Tula's LPP and SPP for my reloads. I never had problems of a misfire etc with both. I individually...
Forum: Factory & Surplus Powder
Thanks for posting powder availability from Bruno's. I just ordered 4ea 1lbs Bullseye. A bit higher than usual but have been seeking through the internet for months to no avail until your post....
Forum: Factory & Surplus Powder
I just came across somebody's post a couple of minutes ago & can't remember which member posted it but according to his post, Bruno's have some powder. I went to Bruno's site and ordered 4 ea. of ...
Forum: Casting Equipment
I had the same problem last night with the gray muffin pans. As soon as I get the two ingots that are stuck from my previous smelting, I will sand the bottom and walls of the muffin cavities and let...
Forum: Cast Boolits
Well, I was just surprised because I have never used this fluxing process before and was just assuming that the paint on the wooden pencil (mostly blue Steadler) had zinc on it sort of bled through...
Forum: Cast Boolits
Hi! Just finished melting two muffin trays of lead strips. Used this same lead strips before in my casting and had no problems. Tonight, I was skimming the dross off and had saved a ziplock bag of...
Forum: Cast Boolits
Never used that mold but have a bunch of Lee's for 45 ACP. Sure looks like some nice bullets. Good find for the price of the RCBS mold. Info us on how it punches holes.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |