No worries. I guess that I’m not old after all…..I understand 351 Self Loader
Type: Posts; User: Cast10
Forum: Helping Hands
No worries. I guess that I’m not old after all…..I understand 351 Self Loader
Forum: Cast Boolits
Thanks for the info. I found another partial can and it was all grey. It was from 1996. Also, a friend with me noticed lots of smoke when I fired it. W231.
Forum: Lead and Lead Alloys
I just had Tom make me a mold. It was published to drop at 117gr using COWW. My mix is SOWW + some Hardball to add in SN. I end up around 1% SN 2.57% SB and 96.4% PB. In the ordering process,...
Forum: Cast Boolits
New discovery this week. I had run some test loads without chronographing, just seeing which load was more accurate. This was my first mistake. I usually chrony all test loads while shooting...
Just a brief note to remind you that when you reload cast bullets that are larger than jacket, you may have to use an M-die expander to stretch the case enough in order to not bulge the case, while...
Forum: Factory & Surplus Powder
HP-38 and TiteGroup for my 32-20……Been using 231 but hard to find.
Forum: Military Rifles
I shoot AA2460 in my M1’s.
I know 4064 it is within burn rate, but I’ve heard some things about pressure. Even though 2520 was THE service rifle powder, I didn’t go that route either. Used...
Forum: Cookin' Recipe's
I use a locally made breakfast sausage and make milk gravy. Don’t forget the biscuits!
Forum: Helping Hands
On the way…..THANK YOU SIR.
Private Message sent.
Thanks Froggie.
I’ve read and read and read about the 32-20 here, every aspect. Reloading had some challenges, but I only crumpled one of the first five test rounds loaded! I learned You gotta go...
Forum: Muzzleloading.
Got it too! I blocked the email, which was not directly from Muzzle-Loaders.com.
Forum: Cast Boolits
I use hardball with SOWW’s. Basically, 5.25lbs hardball to 7# SOWW’s. Give me 11.3 BHN and shows some expansion in soft berm. I get good fillout in the molds.
SN 1% SB 2.57% PB 96.4%
Accurate molds 4 cavity aluminum 31-117A
https://accuratemolds.com/
https://castboolits.gunloads.com/showthread.php?468104-32-20-WCF-Accurate-31-117A-Powder-Coated
Dodging rain showers, got to finally shoot my test loads for the S&W 1905 3rd change 4”. These were powder coated with Smoke’s Flame Red and the bullet was from Accurates clone of the original...
Forum: Coatings and Alternatives
@lpel Thank you sir. I’m kinda fond of them. Hope they shoot well.
Forum: Lead and Lead Alloys
When I began this rabbit hole, I dove into learning about alloys, mixes, calculations, etc. I arrived at a mix whereby I could use SOWW’s, which were plentiful at a local shop, and Hardball from...
Forum: Coatings and Alternatives
Flame Red from Smoke. First time using this color, but for a wheel gun, hey, gotta have it!
https://i.imgur.com/18TOP2L.jpg
https://i.imgur.com/Hade1oL.jpg
It dropped at .315. It was designed for .314. I will size after PC to .314. Have not sized, nor PC, nor loaded as of yet. Ranch work this weekend, so hopefully next weekend I’ll load some up.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |