why not just rig up some kind of spring or elastic bungee to keep the lever tight
you know take a bungee wrap it around the shaft once then attch it to the table and the other end to the lever
Type: Posts; User: bohokii
Forum: Casting Equipment
why not just rig up some kind of spring or elastic bungee to keep the lever tight
you know take a bungee wrap it around the shaft once then attch it to the table and the other end to the lever
Forum: Cast Boolits
i shoot lead in my glock 21 and imi baby eagle .45
i heard its not good to do that in polygonal rifling so i bought replacement barrels for both and have been just fine so far
i figure the...
try just using a spoon make sure when filling you just spill it all over the place it seems to work fine for me i get good fills
Forum: Cast Boolits
seems all my tire guys have agreements with "interstate batteries"
Forum: Our Town
yes airplanes can only lift off within maximum load
http://www.usps.com/shipping/prioritymail.htm
i think the 20 pound limit is for international shipping
the envelope rule makes sense...
Forum: Our Town
my post office told me they could not allow me to ship in the flat rate envelope unless it was sealed "only" with the adhesive strip provided
i had mine taped up
so what i did is just put the...
Forum: Reloading Equipment
i use vasaline it comes off the cases as easy as it goes on
i keep a greasy finger to rub on a case then drop them on a white towel
just rub them on a towel when there is a bunch
and its...
yea well either way you're gonna make lots of noise
Forum: Gunsmithing Tips & Tricks
hmm better not hold the mag on a tec 9 then
http://members.shaw.ca/tmcveigh/Projects/GunRights/images/Intratec_TEC9.jpg
Forum: Gunsmithing Tips & Tricks
its basically the same as a g17 but has a little nub that comes down from the slide when full is selected and it pushes down the striker release
it is made so that you cannot switch the slide with...
Forum: Lead and Lead Alloys
i am down to 134 pounds of my lead muffins i'm staring to get the shakes
http://i43.photobucket.com/albums/e366/bohoki/DCP_7915.jpg
Forum: Casting Equipment
ive done so many with a skillet and a spoon
Forum: Reloading Equipment
gee why didnt they jsut have it slide in and have you drop a couple pins through
to remove pull the pins pull it out
ive kind of already been using a system like this i just have my presses...
Forum: Our Town
well i have to agree with the moron cause my lead fouls my bore just like my dinner fouls my plate
i just clean it before i put it back in the cabinet
Forum: Gunsmithing Tips & Tricks
funny it seems the atf is ok with using a bipod on a pistol
http://www.impactguns.com/store/media/ruger/ruger_4901.jpg
and those can be gripped and used
...
Forum: Cast Boolits
put me down as a cheapskate
although i like the idea of making it myself kind of a spirit of "self reliance"
of course i cant make powder or primers
Forum: Cast Boolits
the lead should melt out the bottom i wasnt aware that spain made any tmj encapsulated ones
Forum: Casting Equipment
teflon is normaly on aluminum i dont melt with aluminum its weakeness point is too close to overheated lead
steel has 1000 more degrees from the hottest i can get with propane or liquid fuels
Forum: Our Town
wha!!! how is this any different than an 80% lower that people finish?
Forum: Cast Boolits
i whack the sprueplate with the thing i use to beat the hinge to get the stuck bullets out
Forum: Reloading Equipment
seems to be a solution for everything if you throw money at it
http://www.youtube.com/watch?v=SGYLmHvKVd0
Forum: Cast Boolits
i run my bullets through the sizer unlubed
about every 10th one i rub a bullet on a candle so maybe that is using lube
but i just send through my lee tl design bullets just to true them up i...
Forum: Cast Boolits
i started out with about 5 pounds of wheel weights and though hey i pay $35 for 500 cast bullets from the gunstore
if i can get some gear that would be less than that it would pay for itself...
Forum: Cast Boolits
i use a coleman stove but i use a 6 inch skillet its hard to keep a big container hot
also the pumped white gas ones need to be well pumped and you have to use the knob to extend the tip cleaner...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |