I will take the
Lee 6c new
356-125-2r $40
Type: Posts; User: sgraham3
Forum: Completed Deals
I will take the
Lee 6c new
356-125-2r $40
Forum: Completed Deals
I have a Do-it Walleye Jig mold whb-1064 I would like to trade for a buckshot mold.
259513
259514
Should have said the Marlin is a 35 rem. I hope to get more than one but right now lam looking at these two. I would like to get a mold that works good in both. I got some wfn but haven't found any...
I have a Marlin 336 pre micro groove and Ruger gp100 and looking for a mold that will work well in both. I am looking at the 360 180Gr. RF (BRP) and 360 180Gr. WFN from NOE. Does any one have any...
Forum: Group Buy Archives
I'll take a 2 cav GC, with top punch. and 1000 gc,s
Forum: CB Loads / Military Rifles
I tried 35gr H4895 and was all over the place.
This mold is in the group buy section and it looks nice. I am new to casting and looking for a mold for 35 rem I recently picked up. I have read all over the net the RCBS 35-200 FN is an excellent...
Forum: CB Loads / Military Rifles
shredder
I have have seen a filler recommended before with this mold. Have you tried a dacron filler?
Forum: CB Loads / Military Rifles
sorry should be .325. I also have a 7x57 Mauser Iam working on. Paper patching sounds interesting, I have no knowledge of that but sounds like some reading. I will try to get a impression of the...
I seem to have one lee does not make a mold for, 35 rem. That's why I was seeing if there were any other makers that were not as pricey.
thanks everyone. going to have to save a little longer.
Forum: Reloading Equipment
ok. I found a pdf of on the layman site.
Forum: CB Loads / Military Rifles
its a 1942 German sporter. The bore measures .285. I dont how to get the throat size. I have tried 13gr greendot. 35gr H4895. I dont remember exactly i will have to check but I believe around 40gr...
I am new to casting and looking for a couple molds and was unable to find any other bullet molds in the price range of lees. Are there any out there?
Forum: Leverguns
Thanks. I am currently researching molds but would like to try some boolits first, if i can get my hands on some. I picked up a set of lyman dies at a show and they crimp it nicely. My have to check...
Forum: Reloading Equipment
Thanks, I have never seen such a small seating stem. How do you set up this die?
Forum: Reloading Equipment
Picked up a set of Lyman dies in 7mm at a show, i have one die listed as DA. Because of the thumbscrew top, I'm guessing the "DA" die is the bullet seater but it has a long skinny plunger . Can...
Forum: CB Loads / Military Rifles
I bought the 8MM Karabiner and have been trying to get it work. I have to seat it way back to the shoulder to get it to chamber. I have tried 4831 4895 and greendot gaschecked. The greendot does the...
Forum: Leverguns
Very nice. I just picked up a 336A in 35 rem, hope mine shoots that well.
Forum: Leverguns
Thanks guys. That makes sense. I will give it a try.
Forum: Leverguns
I have tried factory ammo and all of it has fired. Some old Federal and some Remingtion. I defiantly resized all the way to the shell holder. How much should I leave it off the shell holder and will...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |