Thanks Guys I'll give those ideas a go
Type: Posts; User: stuffy
Forum: Coatings and Alternatives
Thanks Guys I'll give those ideas a go
Forum: Coatings and Alternatives
Hi all I have been following the progress and would like to try this but here in oz 6mm airsoft bb's are illegal so does anyone know what sort of plastic they are made of so i can source some in a...
TXGun shoulders ok but I have a slip on recoil pad on at the moment to increase my length of pull. Before my eye injury I shot it open sights and A day at the range often ended in a blood nose from...
hello guys
I'm wanting to load some 158 grain powder coated bullets for cheaper practice and messing around in my 35 whelen rifle but I have not been able to find any published loads. I have...
my rifle weighs 7lb2oz bare i haven't weighed it with the scope on. I haven't chronographed any of the cast loads it is on the cards but first i need to replicate my groups and see if the scope will...
I finally got myself sorted to go to the range - turns out I didn't break the old red dot But i did shoot the barrel loose on my rifle (its a remington 7600) so I disassembled all the way cleaned...
I finally got myself sorted to go to the range - turns out I didn't break the old red dot But i did shoot the barrel loose on my rifle (its a remington 7600) so I disassembled all the way cleaned...
hi everyone just back from the range what a thoroughly unsuccessful trip I re-sighted the red dot that is the backup scope on this rifle but couldn't reproduce the groups i got last trip so I...
I'm using ar2206h. At the moment i am doing a long ladder test 1 grain either side of 44 grains shows promise. I am only shooting at 50yds to reduce my errors. I will be going to the range this...
water dropped blammer but I need to work on my consistency i am still discarding 25% percent or so of my boolits
Stuart
Hi Guys
I finally got to where this boolit is showing promise.Sorry it took so long to get back to this project but it broke two scopes and I had two hunting trips to attend to.I had to reduce the...
Forum: Boolit Lube !
Buck shot one of the moderators here makes them
send him a pm
Stuart
I finally got my stuff together and loaded a few rounds
so off to the range this weekend to see how they work
I attached a couple of photos
Stuart6001560016
Fosters is good nowhere
Once the rain stops here I should get a chance to see where this goes
Stuart
robroy how dare you ask a Queenslander for the devils drink and in cans no less:kidding:
stocker and stephen ar2206h is going to be the first powder I try as thats the powder I use with jacketed I...
No blammer I'm not waiting for checks from you or complaining just being impatient cause no one locally had any
I went and measured some as cast and measured 1.22 inches . No I haven't loaded any plinkering loads yet
Stuart
Thanks for the replies I've found some published data in Lee's modern reloading for h4895 which I already have and winchester 760 & 748
Both are for j words but give me some where to start
Stuart
sounds good i'm still waiting for my gas checks to arrive so I can't play
Stuart
Hi fluxed I need to achieve 1800fps to stabilize by my calculations and probably a little faster
Thanks for the interest I E-mailed the two powder companies that readily available both were little...
Forum: Cast Boolits
After a two year delay i finally bought my first mold and cast some boolits and thought i would share my excitement and the results57807578065780857809
The mold is a 360-300gc from cast bullet...
Ok I have stopped procrastinating and bought a mold to suit my 35 whelen but can't find load data to suit. The mold is a 360300gc from cast bullet engineering here in Australia, easy to get powders...
Try http://www.castbulletengineering.bigpondhosting.com/custom.htm the site is a little confusing it is organised by introduction date then calibre but he does ship to the internationally and has a...
Thanks for the welcome Buffalo in Australia top out at a little over 1000kg
Hi i,ve got my first whelen on order and I am looking for a starting point for loading lead bullets for it in two areas. A sub 180gr or less bullet for my walks in the scrub, ranges <150 metres and a...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |