My Girlfriend has a Walther PPKs and a Colt Frontier but if I aint paying attention she will try to steal my Kimber. She loves the 1911 and shoots pretty respectable with it.
Type: Posts; User: drklynoon
My Girlfriend has a Walther PPKs and a Colt Frontier but if I aint paying attention she will try to steal my Kimber. She loves the 1911 and shoots pretty respectable with it.
Forum: Cast Boolits
45-70,
I had a stainless 4" a while back and it had bad cylinder throats in it. In fact, one had a deep spiral tool mark in it but that was my fault for not checking it. I have no idea about...
Forum: Cast Boolits
Jetsfan,
I think I understand where you are coming from. However, reloading can be quite the art form and there are a lot of factors that go into a decision such as powder choice. If I were to...
Forum: Coatings and Alternatives
I called swede and the answer is that the bullet is intended for the .416 gas checks. Now I read on here that the shank diameter for the .416's is .395 and I am at .389. That is only a .005+-...
Forum: Coatings and Alternatives
Jcren,
I appreciate your response. I emailed AL at NOE. I'm thinking this may be an issue where the mold was designed for 416 gas checks and not the 41's that I bought from him. Hopefully this is...
Forum: Coatings and Alternatives
The shank measures at .389 the id of the check is .376. The check thickness is .017. so the OD of the check plus the shank is .423. I am sizing to .410. This is not going to work is it?
Forum: Coatings and Alternatives
Ok, I read around and I will try the toaster oven method of annealing. Hopefully this makes the difference that I need.
Thank you
Forum: Coatings and Alternatives
Jcren,
I am PCing that is why I put it in this section but in retrospect may not have been the best place. I tried the Lee Push Thru sizer to seat the checks and this did not go well at all. I...
Forum: Coatings and Alternatives
Fellow casters,
I am working on building a load for a new .41 Mag. The mold I choose was NOE's .412-238 WFN GC http://noebulletmolds.com/NV/product_info.php?cPath=40&products_id=1794. The...
Forum: Coatings and Alternatives
argggghhhhhh I waited to search this topic until I had a problem. I have 300 .41's coated. I just got me Lee PTS and tried to seat my checks. That is a no go for this bullet. I'm moving lead trying...
Forum: Reloading Equipment
NC, it's a GE tube radio. its still hanging in there.
Forum: Cast Boolits
Shoot-n-lead, I second that. I was in the BPS last week and picked up a pound of 2400. They had more left and I figured i'd leave the rest for the next guy.
Forum: Reloading Equipment
Well, I have posted on this thread three different times I think. Each time right after I moved. This time its taken a while because I bought this house and I wanted to wait until the reloading room...
Forum: Cast Boolits
I poured a few .358's and I built a shelf to put my dies, powder measure inserts, and shell plates in. I also deprimed a gazillion (give or take a few) .38 special/ .357 brass. I reorganized my ammo...
I'm a user of the SPP brass. Mainly I stick with Federal and Blazer the headstamps appear to be out of the same factory but I may be wrong.
Four-Sixty,
I never considered sizing them backwards. You are a genious. I don't know why ideas like that do not come to me easier. I swear I get use to a procedure being done a certain way and...
Sw thank you. I got my mits on some 2400 today and my mold from Al was in the mailbox when I got home tonight so it is almost time to start experimenting. My first step is to cast a few soww bullets...
Looks good. I can see a use for it outside of what is loaded on the progressive for sure.
Lucky,
Thank you that is exactly what I was after. Is that an Accurate manual or a caliber specific manual?
AnyCal,
I am surprised that your throats are that large. Many, including me, have been complaining of too small of throats in new Rugers. I would check the barrel and see what it is in...
Anycal,
Sorry you are having issues. I know how frustrating that can be. Some may argue this; however, if you are leading "lots more than expected" then you can discount the accuracy tests as...
So, I took it down today and processed the 20 rnds of winchester. Man this thing is great. It rolls a bit in the hand but it isn't a problem or abusive. I am attributing this to low bullet weight...
Lefty,
Thank you. That is a lot of good information. I hadn't really considered Blue Dot but I did see some loads for it. Unfortunately, the powder choices in my Cast Bullet Handbook #3 are...
Forum: Reloading Equipment
I'm not sure what kind of sack may reduce case sticking without reducing effectiveness. Right now, I am planning on just waiting until I have a large enough batch of one caliber or only matching...
Congratulations Petroid. I am a 1911 lover. I've got a RIA GI model that is very nice and surprisingly quite accurate. Well, not that surprising if you have dealt with RIA 1911's. I've also got a...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |