Search:

I'll slug the bore. I've search but have come up empty on 405 info/posts here.

anyone cast for the 405 Winchester. I read a bit that .413 work better.

I have a modern 405 1895

Lee powder dipper set from 1966. $5 + $10 shipping = $15
I believe it was never used. Check or Money order is fine.

https://i.postimg.cc/5yxvYDJh/Lee-dipper.jpg

Rich J.

I dropped it to 3.7 This was in a Dan Wesson 357 but I may also shot it in a 5-shot so better safe.

These are plated Berry's

I have a ton (big can) of 700x, Don't load shotgun anymore.

I think it's a bit fast but I have been using it for 38spl 158 berry's . Might be warm at 4.0gr
It measures better than Unique (don't...

This is interesting. Will try it next time. I can tell you if I get a case stuck in the rockchucker sometimes the co-ax press will pull the case out.

BIG IF you have a co-ax.

I had the 2 1/4" drive case prep bases from Herters but no bits for it. All the new stuff is 8x32 (kinda). i bought 4 Standoffs from McMaster that are 8x32 inside thread and 1/4 OD.

The tool is a...

Herters. old catalog.

https://i.postimg.cc/xCMZBgCt/deburr-herters.jpg

suggestion was Herters. I think that is it. Pop had a Herters Press and Dies. I have an old catalog around, will investigate :-)

Should add that they are at least 50 years old

Hornady LNL stand for an RCBS Measure. Uses the RCBS footprint and thumbscrews into threaded inserts.
Have to buy the LNL conversion kit. 1 3/16 boring bit (Irwin bit will do) . Had to open the hole...

In this day and age of Fast fast fast. I have 2 primer pocket brushes and only the outside neck deburring die.

Does anyone remember who made these? Not even sure what to call them.
...

MTM, found the funnel.

OK now I have to find the funnel thanks.

I 'm assuming Lee , being red, but I can't find them online.

They are marked on the top edge 17, 223, 30 and the long one is unmarked.

So what are they?

...

My black Bonanza has a set screw to hold the ring of the dies not a snap in spring.

I once had a stuck case , ripped part of the rim off in the Rockchucker.
Screwed the dies out, popped it in the Co-ax and pulled the case right out.

PS my press is an older one with the hex...

Good Luck and very cool, I have the same 3 Speer books. I'm really sorry I dumped the American Rifleman and G&A. I had Pops collection from 1960 to 1995.

dug these out, some bad some ok.

https://i.postimg.cc/4xCj5hXj/boxes-1.jpg

https://i.postimg.cc/7YJp0Nrg/boxes-2.jpg

split rings..co-ax for me too

Rockchucker, Co-Ax, Dillon 650, Herters, Pro-7 in parts, CH in parts,

Never used the CH but I think I have all the parts. I did use the Pro-7 but retired it.
...

I put a question to Hornady about the Pro-7 parts interchange. I also see a member here made shell plates from the new press to fit the Pro-7. Is that the only parts that may work on the Pro-7.

in a pile of stuff == 30-06 necker and decaper and 30HH necker and decaper

https://i.imgur.com/ktfqVTL.jpg

Speer 3,6,7 and Lyman 45
I think I have 2 more somewhere. Probably newer.

http://home.pipeline.com/~shootzn/reloading-manuals-1.jpg

Speer 3 has 30 and 32 Rem