Search:

still waiting on my german made sling and yet to decide on scope or scope less. found an old lyman out of production .318 mold. found some jacketed .318 bullets (just to have on hand )

pictures...

GREETINGS,
didn't know what one was or that they existed. Got a good deal on one with double set triggers so high bid and won. After searching the internet for missing buttplate, rear sight and...

Have not been here for quite some time.
would anyone have any leads on a Forester tap o cap maker or something similar ?
would like to give that a try.

maybe a gas check maker could form one up...

JonB.
think you hit the DAMN nail on the head.
ran another batch of 452-228-1r . This time I was pretty stingy on the powder coating set oal at 1.21 chambered an fired fine.
loaded with 5.0gr of...

ok so tomorrow cast a few , and don't powder coat see if they fit
start of a plan
casca

bullet drop test worked fine
didn't think to use empty brass casing.
factory rounds fitted correctly in to all 3 barrels.
also put rounds back through the sizer die to see if that would be of any...

Greetings,
I am stuck ! I casted then powder coated and then lee sized these bullets to .452 loaded 125 of them . Went out to test fire and the rounds will not chamber. seated at 1.27 PMC brass ...

the black Teflon & gray came from ALL POWDER PAINTS .COM 9MM RED is HF rest of the colors came from POWDER BY THE POUND
bands and grooves are not filled just looks that way in photos most coated...

ok up for review is my attempt at powder coat SHAKE & BAKE 15 minute shake in plastic coffee (can)
pop into toaster oven , then off to the lee sizer die.

casca92998

I have been shaking em in small coffee plastic can. 5 to 10 minutes works outstanding. why tie up a tumbler ? use different shaker for every different type or color.
casca

I have been tinkering with this since before June, THE DRY COAT OR AS I LIKE to also call it SHAKE N BAKEis by far the best method as far as time is involved. SPRAY is by far prettier .. BUT I wanna...

thank you , rob
will get both my digital scales checked perhaps my eye glasses also

Can't seem to find any good data for a 245gr cast & powder coated bullets for the 454 casull ?
Lee Mold , but it's out in garage and I can't remember mold number.

may use some of the bullets in...

while stationed in BERLIN FRG. the CZ -75 was the cheapest firearm a GI could buy at the gun club. $ 190 no import marks. most everyone in the STINGER PLATOON had one . I left a Guns and Ammo...

still no leads or luck ! anyone want to part with the one they have ?
thanx
casca

I have access to an FFL all three of those are strikeouts, where did all those revolvers GO ?

Greetings,
I have been on the hunt for a Nagant revolver, would anyone know of wholesaler or retailer that may have some in stock ?
...

Greetings,
I am pondering the purchase of the fairly new QUICK TRIM DIE CUTTER SYSTEM ?
perhaps there maybe a few here that have purchased and used the system ?

ANY COMMENTS ?

casca

greetings,
is there anyone doing much shooting with the 9mm Blackhawk ? i am currently using lee 124 gr powder coated bullets with 3.2gr of 700x . Why 700x cause I had 2 cans on the bench.
...

that comment was on the MONEY, primers are pretty hard to find here outside of CHICAGO.
casca

How is the group when you remove forearm ? bet it tightens up !
casca

I have some about (150 pieces) of this lake city 30-06 match brass stamp numbers 61-62-63.
is there anything unique about this Brass or lot numbers. I have 1 30-06 and it's a handi rifle.
...

using a THUMBLER'S TUMBLER NOT A THUMBLER'S VIBRATORY
brass was cleaned didn't effect how 223 ammo was shot both from a single shot and an AR 15. Perhaps YES, it would have been better for us that...

here is my plan, going to tumble them over night. then seperate them again from the media and stick em back in tumbler with just brass that i hope should clean em up enough.
let ya know.
casca

digging through my boxes of treasures found 400 primed 223 brass
250 primed 7.62x39 brass
...