RepackboxMidSouth Shooters SupplyWidenersReloading Everything
Lee PrecisionInline FabricationLoad DataTitan Reloading
RotoMetals2

Search:

Type: Posts; User: akajun

Page 1 of 30 1 2 3 4
Results 1 to 25 of 743

Search: Search took 0.01 seconds.

  1. Replies
    53
    Views
    1,945

    Forum: Our Town

    Controlled burning reduces tick numbers as well....

    Controlled burning reduces tick numbers as well. What about the sacks of pesticide powder i see hanging under cattle feeders, in barns, etc? I would think that would be effective as well from a...
  2. Replies
    18
    Views
    1,030

    Yup Modern high temp bearing grease is best,...

    Yup
    Modern high temp bearing grease is best, especially on the line or in the south
    When temps rise or the gun warms up, lubriplate and most other grades run and fling
    Red high temp bearing...
  3. Replies
    23
    Views
    875

    Duracoat and durafill

    Duracoat and durafill
  4. Replies
    12
    Views
    843

    Forum: Our Town

    IIIRC youre in Vicksburg, so those are Miss River...

    IIIRC youre in Vicksburg, so those are Miss River Barges. Not often do they take them out of the water for repair, usually most stuff is done in water, unless its really bad like major welding,...
  5. Replies
    28
    Views
    1,636

    for that price you can send it out and have it...

    for that price you can send it out and have it back bored and extrusion honed and keep most of that money in your pocket.
  6. Replies
    37
    Views
    2,853

    Way back when I got in a group buy for a special...

    Way back when I got in a group buy for a special run of Lee 5.45 dies, I simply formed brass from 556 nato brass. simply trimmed, it about 10-.20 thou long, sized in a 222 die, then anealed it and...
  7. Replies
    18
    Views
    757

    Ptg unithroater is what you want No lathe...

    Ptg unithroater is what you want
    No lathe needed, turns by hand and stays concentric to the existing throat
    Most throaters need to be used in a lathe to get good results.
    Before you do that...
  8. Replies
    9
    Views
    703

    WTS bump

    bump
  9. Replies
    28
    Views
    1,636

    Brownells sells a kit which is a modified brake...

    Brownells sells a kit which is a modified brake cylinder hone
    Comes with different grit stones .
    That’s what I use, but keep in mind, if it’s badly pitted you bay need a backbore reamer to fully...
  10. I’d like to see him also test those same barrels...

    I’d like to see him also test those same barrels with an xrf gun to determine composition
    While hardness is important, steel composition is important as well and annealed 4140 can be similar in...
  11. Replies
    9
    Views
    703

    WTS Bump

    Bump
  12. Replies
    9
    Views
    703

    WTS Bump to top

    Bump to top
  13. Replies
    9
    Views
    703

    WTS Bump No reasonable offer refused

    Bump
    No reasonable offer refused
  14. Replies
    9
    Views
    703

    WTS Bump

    Bump
  15. Replies
    9
    Views
    703

    WTS Bump Make offer

    Bump
    Make offer
  16. Replies
    9
    Views
    703

    WTS Bump

    Bump
  17. Replies
    10
    Views
    727

    Doubt it was a squib or stuck bullet If I was a...

    Doubt it was a squib or stuck bullet
    If I was a handgun maybe , seem plenty of bulged 38’s, 9mm’s etc but even at low handgun velocities the barrel is sufficiently bulged on the outside to be seen...
  18. Replies
    9
    Views
    703

    WTS Saeco lube sizer w/ dies and punches

    Old dirty but functional Saeco lube sizer
    Has unknown number rn top punch in it with a .356 size die

    Also included are a .3575 die
    A .429 die
    And .450 top punch

    $125 shipped OBO

    Unable...
  19. Replies
    8
    Views
    452

    WTB I have 100 pieces once fired federal In factory...

    I have 100 pieces once fired federal
    In factory boxes
    Make me a fair offer shipped
  20. Replies
    16
    Views
    1,675

    Forum: Shot Guns

    Mike orlen

    Mike orlen
  21. Replies
    15
    Views
    775

    ridgid dark or oaty dark, all I use for stainless...

    ridgid dark or oaty dark, all I use for stainless and cm barrels.
  22. WTB 35 whelen encore barrel or junk encore barrel in any caliber

    As stated above looking for a used 35 whelen barrel or junk encore barrel I can either have rebored or do a barrel stub job on
  23. WTS Bottom one is muzzle 3.5 throat 3 Damaged thread...

    Bottom one is muzzle 3.5 throat 3
    Damaged thread one is muzzle 4 throat 4.5
    Top is muzzle 4 throat 5
  24. WTS Yes I wrote the throat and muzzle readings on the...

    Yes I wrote the throat and muzzle readings on the Barrel in paint marker

    Plus I bore scopes all three. The damaged thread one and the top one are frosty but good
  25. WTS Wts usgi garand stocks, barrels, and m14 stocks

    3 usgi garand stocks, all three are dirty and need refinishing , dents raised, but serviceable and to cracked $75 each OBO plus shipping

    3 usgi garand barrels , two are serviceable as is
    One is...
Results 1 to 25 of 743
Page 1 of 30 1 2 3 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check