I had the same problem. Pull some sample bullets and mic the size. Even using the most minimal taper crimp still seems to change the bullet size. So , mic the pulled bullets and let us know what...
Type: Posts; User: Tomuchiron
Forum: Boolit Lube !
I had the same problem. Pull some sample bullets and mic the size. Even using the most minimal taper crimp still seems to change the bullet size. So , mic the pulled bullets and let us know what...
Forum: Boolit Lube !
Finally made it to the range. I believe they shot even better than LLA.
Definately less smoke. I think during lubing, the warm-hot bullets allow for a thinner coat of lube. I might have been...
Forum: Boolit Lube !
Still looking for a knock off recipe for LLA. Surely somebody has figured out what is in it.
Forum: Boolit Lube !
Hey, Smokesahoy
If your not leading, I'd say your lube is working. Have you pulled a couple of bullets and see what they mic at. Might be a little smaller since crimping.
I have to agree that...
Forum: Boolit Lube !
Until I can make LLA, I Decided to try again to Use up some of this Ben's Red. You can Melt the Ben's , and add Mineral Spirits Like you would 45/45/10. , Or Ben's/Red/10 ...The trick is heating...
Forum: Boolit Lube !
Still need a recipe for LLA. Surely somebody has figured out how to Duplicate it.
Thanks for all the good response guys. I've learned a lot from this site. Thinking back to a lot of the older...
Forum: Boolit Lube !
I've used 45-45-10 quite a bit but find I have finally run out of those little bottles of LLA. I've read quite a few recipes here and I assume most of them are for sizers and pan lubers. None have...
Forum: Boolit Lube !
Going back to tumble lubing and 45/45/10 type lube. So how do I make Lee L Alox. and Or How can I convert Ben's Red to Tumble lube Mix. Pan lubing is not working out for me.
I tried hot tumble...
Forum: Lead and Lead Alloys
Dry Moly Spray is my helper for all my molds. Mini bread loaves, muffins, lee 1 lbs, etc. seems to work great for every thing. I am now spraying the bullets before going thru the Lee sizing dies. ...
Forum: Lead and Lead Alloys
I've used about everything for moulds. You can spray anything with dry moly lube, and it will release the lead. I have used alot of teflon coated as is and they work fine for years,.
Mike
Forum: Factory & Surplus Powder
Heard a new term the other day. Inert bulk filler. Don't know if it applies to your powder or not. I was using clays univrsal- light loads- 38 wadcutters, and I was seeing white flakes, on the...
Forum: Casting Equipment
Speed up your lee sizer. turn the press upside down and remount it.
then just drop your bullet in the hole. If you get real fast you will pinch your finger. that is where the extension tubes...
Forum: Reloading Equipment
I rinsed some shells and then did a light sudsey wash and rinse with ZIP WAX. Seems to have made the shine last a lot longer. I'm going to continue doing this. Has anybody else tried this for...
Forum: Boolit Lube !
I prelube with silicone spray. Does make sizing easier. And have a lot with no other use for it.
Just a final coat of LLA works for me.
Forum: Casting Equipment
Had to stop at harbor freight and spotted the weed burners, 19.95. Been meaning to get one anyhow. Worked alot better than I Imagined. Shouldn't have put it off so long. Really shortens melt...
Forum: Cast Boolits
In Florida the scuba shops are full off sprays for swim masks.. same thing.
Light dish soap also works.
Mike
Forum: Special Projects
Thanks Imashooter
Thats the best selection of recipes I have ever seen...
Got them saved to file.
Thanks alot.
Mike
Forum: Special Projects
The standard lead wipe cloths for Stainless Steel seem to be temporarily unavailable here in town. They shouldn't be to hard to make. The bags that mine came in say flamable and to keep sealed.. ...
Forum: Reloading Equipment
Is that a bulge?. just on one side? I put my glasses on and it still looks like it.
Mike
Forum: Cast Boolits
"9mm they were not sized" ( wonder what size they started as)
"read .3595 after seated and crimped and pulled " (1st sizing )
"WELL larger than the bore...
Forum: Cast Boolits
I Prelube with Silicone Aerosol spray ,( I have a lot that I don"t need.) ,. Also Like my dry teflon Motorcycle chain spray, I also use it for case lube. Then tumble lube after sizing.
If...
Forum: Cast Boolits
I love Inguinety. I believe reloaders have more problem solving abilities than the other "normal" people at the range. And I thank all of you for the new ideas. It seems so simple now. ...
Forum: Cast Boolits
Just went thru the exact same thing. Your putting .357 bullets in .356 cases. the other replys were all right on que. Pull some of your bullets and see what they now measure. A possible quick...
Forum: Cast Boolits
Just start water dropping after a 20 year break in reloading. Don't like the water splashing up on the hot molds, etc. Tried dropping the bullets on a slide board into the bucket, about 45' degree...
Forum: Cast Boolits
I have the same problem. Mine is a oval bullet out of a round mold. Operator error. When I run the lee 6 cavity to fast and very hot. the bullets deform when they hit the slide board into the...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |