SaltyDog You will have that issue with bright colors Whites, Yellows, oranges ect.
Best I can explain is its like trying to paint a black wall with one coat of white paint.. Its covered BUT you can...
Type: Posts; User: Smoke4320
Forum: Coatings and Alternatives
SaltyDog You will have that issue with bright colors Whites, Yellows, oranges ect.
Best I can explain is its like trying to paint a black wall with one coat of white paint.. Its covered BUT you can...
Forum: Coatings and Alternatives
Glad Its solved. happy hunting :)
.
Forum: Coatings and Alternatives
Since you have 2 bullets coated one with check and one without and only getting leading with the non checked bullet that kind of puts coating and gun issues to the back burner
I would also look at...
Forum: Coatings and Alternatives
About 1600 to 1700 fairly easily
Somewhere around 1900 to 2000 fps you will loose accuracy and need a check
Every gun is different as are powder/ primer/ bullet match
Forum: Coatings and Alternatives
Ral is an industry standard color code.
So any mfg can ,if they want to, mfg a particular color it will match the same color.
The MFG can call it whatever color they want but as long as the RAL...
Forum: Coatings and Alternatives
Will do.
I want to do a few more batches throwing in a couple variables before I declare a winner and get a batch ordered.
Just like to be absolutely sure powder works like it's supposed to...
Forum: Coatings and Alternatives
Sorry but no... not where my powder comes from
Forum: Coatings and Alternatives
OK got some preliminary sample of 2 colors in the running to replace Traffic Purple
did a quick and dirty hard core test batch of each to see worst case scenario coating capability
NO BB's, approx...
Forum: Coatings and Alternatives
adding gas checks would be very helpful in your pursuits
Forum: Coatings and Alternatives
To confirm the above answers yes the PC will absorb moisture and that will kill the ability to create static.
Store ONLY in air tight containers.
Screw Type with a gasket is good
Forum: Hunting with CB's
used to hunt where typical shots were 150 to 500 yds .. Most were 200 Plus . At those ranges I preferred Jacketed bullets for the better accuracy.
Now where I hunt 50 to 100 yds is average so Cast...
Forum: Coatings and Alternatives
Usually 1 of 2 things
1. did not cure at an actual 400 degrees or for long enough at 400 degrees
2. bullets slightly undersized for bore
Forum: Coatings and Alternatives
I shoot exclusively PC's bullets in my CVA Optima 50 cal rifle. Very very accurately.
Kill at least 2 deer a year with.
been doing so fore about 8 years now
Forum: Coatings and Alternatives
I will say almost every PC customer I have shooting 9MM are sizing to 357 or even 358 to get them to shoot properly
If your chamber will not take bullets sized over .3560 you probably only have 2...
Forum: Coatings and Alternatives
I would say yes.. Its like this there is NO issue with cooking longer as long as you oven maintains a fairly consistent 400 degrees. The problem comes in when you have wild swings in temps especially...
Forum: Coatings and Alternatives
leading with pc indicates powder not properly cured .. correct Time and Temp are critical to good pc coating without leading
an actual oven temp of 400 degrees for 20 minutes min on small bullets. ...
Forum: Our Town
I have several customer who use paintball guns to run off Geese. They say it works well
Forum: Our Town
1977 started with a wack a mole 30-06 lee handloader and rubber mallet sitting on the porch steps of a duplex in the swamps of eastern NC.
couple years later graduated to a house in Charlotte NC...
Forum: Coatings and Alternatives
Silica Gel packs work well. Put them in with the powder seal shut for a few days.
Pull the silica gel packs out and stick in oven on 140-1540 degrees and you can dry them out and reuse
Forum: Coatings and Alternatives
At 2100 FPS you are reaching the limit of PC accuracy without a check installed .
I would try again with a check and would bet you see better accuracy
Forum: Coatings and Alternatives
yes I would expect you had some PC adhere to the walls with that much at one time :)
That much PC cant just float to the top. A little too thick its going to go somewhere.
I usually put 100 to...
Forum: Our Town
from the fairly vague description it could be for a 1919 belt fed
Forum: Leverguns
I would call JES. I believe in Oregon. http://35caliber.com
Reboring is his specialty
He did a 308 to 358 for me and if shoots wonderfully.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |