Search:

one 4 cavity PB w/ all pins (including blanks)

Set of handles if that is possible too.

don_peacock (@t) hotmail (d0t) com


Thanks,
AJ

Hi all, long time no see!

I'm building up a 300 Blackout in an AR and want to shoot cast from it. I have a few questions.


NOE only has GC version of the mould available, are there any...

My only suggestion would be to make absolutely sure that the hole is situated in the middle of your lube groove. If you have 1/2 of the hole covered, it can behave as you have described. Other than...

I've not done it, but how about this.

put them in one end of a cake pan in the oven. Turn it to 150F (not hot enough to flash). Put something under the end with the boolits in it. As the lube...

I've installed a bunch of one piece firing pins. They make them in titanium and tool steel. Use the tool steel, as the titanium can shatter. The tool steel pins are cheaper too.

AJ

I have no problem keeping my Dillon tubes filled. My kids and wife keep my primer tubes filled. I have 10 tubes and every 5-600 rounds, I come upstairs for a cup of coffee etc. and swap the empties...

I've used both. The Dillon and their customer service makes them the hands down choice. Check out availability of used presses and price vs new price to see resale value and interest for yourself....

6pt-sitka has it right.

Get a Marlin 94, they are the best most bullet proof rifle for pistol cartridges made and they can take full tilt loads.

For Cowboy Action Shooting, the Marlin is the...

It will be just fine, it will melt after you turn it on again.

AJ

You are correct, I've shot full house loads in my 357's and it does in fact slow me down a touch. But, still pretty fast. If you read my entire post(s), you'll have noticed that I voted NO and...

The guys are correct, powder is the big variable. If you take a small 6 pack cooler and toss a couple of the disposable hand warmers in it, then toss your shells in it (already room temperature from...

I would if you lived across town.

The shipping costs would triple the cost.

I bet someone in your neighborhood would whip you one up for a cup of coffee.

PM me if you really need one and...

Consider the feathers un-ruffled :smile: , My boss had me at level 9 of 10 on the "One Flew Over the Cuckoos Nest Scale". I'm home now and I've dropped back to about 7.5, so all is good until...

Thanks for your .02 worth. I'm sure it is worth it.

Please expound on what will be problematic? Of course a 1/4x20 bolt could be used in replacement of the valve stem, but that would make my...

Yes, the open end of the 1/2" cap was probably ,05" too big, so I sanded it down a little when I cut the grooves. It seals so well, that it won't pull up without applying heat and really pulling...

Nothing but lube is below the valvestem.

I don't know if lube gets up in the hollow, when I pressurize it to remove the plunger, it pushes it out.

AJ

The only Lube I've used with this setup is Carnuba Red (very hard) and the universal heater + dimmer switch. I set the dimmer between 1/3 and 1/2. With about 20-25lbs of air pressure, it feeds...

I don't think I made it clear how I'm using my new plunger.

Here is what it looks like while in use (with the air mod cap).

http://i168.photobucket.com/albums/u193/AJPeacock_photos/IMG_8430.jpg...

They seal well. I had to slowly enlarge the slots, until the O-rings were just the right diameter to slide very snug in the tube.

I put the air modified cap over it and pressurized it, the...

I can assure you, that it works. I've posted a picture of the plunger after I added lube and used the sizer, you'll see that the piston has indeed moved down the tube and compressed the lube. (see...

I gave some thought to making a new plunger for use with the air mod and came up with an idea I think is worth sharing.

Removing the plunger is the best part, sounds like a tater gun going off !...

Good job. I did almost the same thing a few years ago. I had a late season doe tag and a few deer were crossing a field. I had intended on taking a large doe, but one of the small ones was...

Stainless1911,

About 5 miles from the pit. I shoot at the Lapeer Sportsmens club instead. Drop me a note sometime and we can meet over at Tim Hortons for a Coffee.

AJ

A-182, no kidding. I'll be heading over there tomorrow to do it right :p

thanks,

AJ

Reading this thread inspired me last night. I decided that I should be able to do this mod with nothing more than stuff available at Home Depot.

Here are some pics. It's not the most elegant...