For my range lead smelting i run 2 14" dutch ovens over 225k burners. I start with an inch or 2 of solid lead in the bottom of each pot and put a dose of material in. The stuff i have seems to be...
Type: Posts; User: bajacoop
Forum: Casting Equipment
For my range lead smelting i run 2 14" dutch ovens over 225k burners. I start with an inch or 2 of solid lead in the bottom of each pot and put a dose of material in. The stuff i have seems to be...
Forum: Lead and Lead Alloys
What does everyone do with all the leftover jackets?
Forum: Lead and Lead Alloys
Anyone ever used any of this before? Any thoughts on it?
Forum: Lead and Lead Alloys
I am always looking on facebook for lead and never get that lucky. Im in your area if you ever run into more than you can use.
Forum: Lead and Lead Alloys
Most of the lead in a battery is in the lead sulfate paste. This takes a little more than heating it up in a pot to get the lead out of it.
Forum: Casting Equipment
I use the KAB4 setup from amazon and have no problem with a 14" dutch oven filled to within about 2" from the top. That is around 200-250 lbs of lead.
Forum: Casting Equipment
You can get a big dutch oven for around $30 at Academy sports. Melted several thousand lbs in one with no issue.
Forum: Casting Equipment
I use an older model of this https://www.amazon.com/Bayou-Classic-KAB6-Cooker-Guard/dp/B003B7USOM with a 14" dutch oven. I put a sheet metal shroud around to help block the wind and hold heat and it...
Forum: Lead and Lead Alloys
It all depends on what schedule of pipe you get. If it is a piece of sch 10 or something maybe but a schedule 40 or 80 pipe would be plenty strong.
Forum: Casting Equipment
But with electric you simply can not input the same number of btu's Even a modest 80k btu propane setup is equivalent to about 23,000 watts, which is around 100 amps of 220v, likely more than your...
Forum: Casting Equipment
If LP is too slow then electric will be even worse. Are you draining completely between? If you leave a little pure lead in the bottom (let it freeze up if you have dirty scrap) then add the scrap...
Forum: Casting Equipment
You normally leave them partially full to lessen the chance of crud getting in the spout and plugging it up.
Forum: Lead and Lead Alloys
Unless you can process in a furnace hot enough to to break down the lead sulfate paste into lead and sulfur emissions there is not enough to worry about. Places that recycle batteries for the lead...
Forum: Casting Equipment
I have built a similar pot that i use to ladle cast and feed my rcbs hot metal. Would you be interested in building a pour mechanism for me that I could install on my pot?
Forum: Casting Equipment
I built a similar sized pot and used a 2600 watt heating band. And it takes about 30 min to melt 100 lbs. I dont have it insulated yet but i imagine that will cut it down some. It puts out enough...
Forum: Casting Equipment
I have 2 small bathroom fans that sit right above my pots, they are ducted over to the window with dryer hose. I made a piece of 2" foam to sit in the window sill and cut holes to put the dryer hose...
Forum: Casting Equipment
I found academy sports has pretty cheap cast iron stuff. I bought a 14" dutch oven for smelting for about $40.
Forum: Casting Equipment
Seems like it was a thermocouple problem. I replaced with a new one and it seems to read ok, but will read 0 if the wires get bumped or something.
Anyone have a link for a good thermocouple that...
Forum: Casting Equipment
I have a couple used 20 lb lee pots i would let go for pretty cheap. They have had a lot of lbs ran through them. The spout and control rods have been replaced but could use s little tlc to lessen...
Forum: Casting Equipment
I have it wired up just the PID shows (i can post it later on) and everything worked fine to start with so i don't think it is a wiring issue. I will check the ice water and boiling water and see...
Forum: Casting Equipment
Here is a list of my parts
K Type 5/16" Thread Dia 200mm x 5mm Thermocouple Probe 2M Cable
MYPIN PID Controller
SSR's 24V-380V 40A 250V SSR-40 DA Solid State Relay Module 3-32V DC To AC
Using...
Forum: Casting Equipment
The probe is still covered. The temp drops without solids being added in.
Forum: Casting Equipment
I have it set in celsius and it has been since the startup.
It seems to bounce around a lot. It reads fine at ambient. Last casting session it read pretty close when lead was up to temp and...
Forum: Casting Equipment
I do not have it hard mounted and it moves around some. Wouldnt have thought they would be that delicate. I am going to order a new one and see.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |