Search:

You need a thick enough steel plate mounted on rock solid table.
The most important thing is the total height of the table steel plate included.
I missed the plate and had to place riser between me...

here you have some shopping list :
one piece
http://www.ebay.com/itm/5-way-2-position-Solenoid-Valve-Air-BSP3-8-DC-AC-Inner-Guide-Pneumatic-Electric-/121362663528?var=&hash=item1c41c74868

two...

Here you have some motivation. It is irracional to pay hundreds of dollars for derimming machine when you can build your own under 50$ (compressor excluded).
Have a look at my configuration which...

Very nice looking bullet with extra small meplat.
It was finished after swaging or it was made in swaging process?

Impossible to do so.
I have tried and with a luck just for about 1000 cases after that the die become loose because the trimmer shaved the inner edges and the trimmed case looked like chewed...

Guys no drilling not even to think about. I am processing thousands of brass at once a year and that time is stressful :-) The press (1050) is getting stuck because of non ejected primers or stucked...

The Lee send me the replacement charge free within two days after complaint. I will inform you regarding replacement parts received. If the Lee will not be willing to send me replacement I will try...

What to say premium service !


Hey Rasto,
Thanks for sending in the photo. We'll get a replacement sent out to you in tomorrow's mail.


Sincerely,
Raquel

My processed brass was spend so another batch was on schedule. As you can see the results are still the same. I have de-primed around 4000 cases and had to stop due to the shortage of Lee decapping...

kryogen are you a man or a woman???
I have read your posts and your decision making process is chaotic and unpredictable lime women have!
First of all, do you have the money to afford 1050?
If...

The Lee has one disadvantage which is the decapping rod. When the flash hole is narrow it will loose the tip of the rod and you are done.

I will never do the same mistake again. To buy Lee molds again. Cheap means poor materials, craftsmanship and service. No other things to add. Buy steel made molds from normal company.

everything prepared ;-)
https://www.youtube.com/watch?v=bEpow_gKPGA&list=UUMI2Wn9rlMda9tSL8ImZdFw

https://www.youtube.com/watch?v=NwYwo7jB8OI&list=UUMI2Wn9rlMda9tSL8ImZdFw&index=9

I do it all the time. I put few drops into a seal bag (spread over the bag) than put couple hundreds 9mm brass and shake well.
Only problem are sticky edges and powder.

My 2 cents. Finished bullets tumbling in my vibration tumbler for about 2 hours with a bit of citric acid and dish washer cleaner.
The magic is in ceramic cleaning media ;-)
...

I am about to build one of these and have some unanswered questions.
I have 10cm diameter 8cm stroke cylinder which I need to feed.
What kind of hose (diameter, fittings) should I use?
I am...

If I were you, I would contact police to take care of him.
This case is no go.

I am in!

Everybody is afraid of bonding etc. I lube the cut lead wire before core forming. I am not decreasing before core seating and so far I have had no problems at all. Yesterday I shoot a hole in hole...

I see. When I was trying to eject the bullet from the die with smaller then supported punch. The punch penetrated the lead and get stuck on the ejection pin completely :-(
Nice precise work done.

Great looking bullets. I have a problem with big meplat due to the Danr dies. The ejecting punch is so big that I am unable to have meplat like you :-(

According your picture the ejector of...

Yes I meant meplat. Any picture of finished bullets?

What hollow point diameter are you going to make? What is the smallest one what are you able to do?

It seems to be a copy of my motorized one from 2012 ;-)
http://webforum.sk/viewtopic.php?f=34&t=8337