Search:

Greetings

To remove your bullet

Remove the depriming system from your reloading sizer die and resize your ammo to the bottom of your bullet.this will size your bullet down and you should be...

Greetings

The E-clip size is 3.2 x 0.6 mm and the size of the set screw is M4x4 DIN913 (pitch is 0,7mm) copied from M&Ps website

Hope this helps

John J

Your welcome

John J

Greetings

Im trying to find out how long the boolit is from top to bottom

if any one has one of the molds could let me know.

I have sent M&P emails but no reply as of yet
...

Greetings

I have a borrowed mag 20 it is full at the moment so i can only give you the dia of the rod .370 at the top just under the spring.

My wife bought me a mag 25 that is still unused so i...

Greetings

I found this article on the the bobcat intresting..http://ps-2.kev009.com/ohlandl/310/357-44_Bain_Davis/Guns_Ammo_MAR_1979.pdf

you will have to look into the chambers to see if its...

Greetings

I have that mold and my load is 4.2 ww231 sized .358 and loaded to 1.108 and it works in all my 9mms

John J

Thank you for fixing the problem
John J

Greetings

A few things to try

First i found that the lyman 452460 likes to be loaded to an oal of 1.190 for my BE guns to feed reliable.

The H&G 68 oal is 1.230

The taper/roll crimp...

Greetings

depending on how much your willing to pay..look here

www.buffaloarms.com/323-105-grain-round-nose-cast-bullet-mold-for-the-8mm-nambu-1-cavity-jim323105

depending on how much you...

Greetings

I just got a replacement pot for my lee 10#pot that iv been using since the early 70s...because i messed up the original by trying to drill the hole out a little larger..little did i...

Greetings

from an old thread

http://castboolits.gunloads.com/showthread.php?354461-Mihec-thread-question

hope this helps

John J

I think this is what your looking for

https://www.rcbs.com/on/demandware.static/-/Library-Sites-RCBSSharedLibrary/default/dw15e0387c/productPdfFiles/ProMeltElectricLeadFurnaceInstructions.pdf
...

Greetings

I think i found what you were looking for..http://castboolits.gunloads.com/showthread.php?276131-MiHec-DE-CARLI-358-%96-148-Wad-Cutter-Bullet&p=3225758#post3225758

hope this helps
...

Greetings

yes it is pressed in what i did to remove mine was to back the top nut up to the handle then placed in in between the jaws of a vice close the jaws just enough to catch the rim of...

Greetings

I would like to buy

1 boxes - 1000 per bx, 10mm, $95.00 per box
1 boxes - 1000 per bx, 38 Super, $85.00 per box

If still avable.

Thank you

Greetings

I would like to buy these....308 175 gr HPBT 1 box of 500 shipped for $150

sent a pm

John J

Greetings

not sure if this will help but have a look and see if it will for you

https://www.trackofthewolf.com/List/Item.aspx/875/1

John J

something for you to read up on

www.dillonprecision.com/450-jr_350_14_386.htm

https://dillonprecision.net/rl450/

but i think a square deal powder die is what you would be looking for.
...

Greetings

To adjust the temp setting you first have to remove the temp dial from its stud...just pull it to you and it should slide off,then look in the middle of the stud you should see a small...

Greetings

If its a dillon funnel....the short pistol funnels were used with the 450 push/pull machines where the funnel was fixed at the top of the powder die with a set screw.

Hope this helps...

Greetings

Try this next...remove the decaping assembly from your sizeing die and then resize a case.

I think your expander ball is set to high in the die and what is causing your problem.
...

Greetings

Give Titan reloading a try...Lee makes and undersized sizing die for 38/357

I had to get one for reloading 32auto.

Hope this helps

John J

Greetings

I will adopt your mold and give it a very nice home.

PM sent

Thank you
John J

Got mine today-- RH008086563SI 2359 Pembroke, MA US

Thank you MiHec