I have to get to my storage unit I have a nicer one in there. Could retired my old air fryer and get a nice double door version for the kitchen. Sorry random thought
Type: Posts; User: corey012778
Forum: Coatings and Alternatives
I have to get to my storage unit I have a nicer one in there. Could retired my old air fryer and get a nice double door version for the kitchen. Sorry random thought
Forum: Coatings and Alternatives
Never know when you need something
Forum: Coatings and Alternatives
I got a better oven in storage, guess I need dig it out. I do know you can put a pid on one. In fact, built and ready that was for a metal furnace never built furnace it self.
Forum: Coatings and Alternatives
I remember when these topic started. Jumped right into pcing. Bought a cheap Walmart oven, used the same method. Set my timer for 25 mins (know or knew the ovens habits) set to my phone, check with...
Forum: Factory Rifles
Have a 350 legend bear creek upper, only shot jacked out of it so far. Had to pull a Winchester 145gr fmj (dud). .355. Have not slugged the barrel yet.
I have a few bins on hand. Just hope I can make it work
Read that too about x shell holder, not enough metal to hold. May just use a universal decapper die and size on a single stage. Boolet sizing should be great.
Thanks Ed
Planning on using it to size boolets. Trying to replace 2 presses and stream line and cut back on some time
On my lee turrets I don’t even try to resize on them. Neck sizer on for my 300blks. Had neck tension issue and that fix that. Been using doing 90% of my resizing for 223/300blk with my old lee hand...
After weeks of research, reading reviews, videos, last thread here (did not want to hijack it), and the pile of 223 and 300blk brass needing to be done. I order the lee app press.
Any tweaks I...
Forum: Gas Checks
Humm, maybe I measured something wrong. Would not be the first time
Forum: Gas Checks
Have some disc size and punch size information
Disc 15/32”
Forming punch 47/128”, 3/8 may be close
Forum: Special Projects
Ended up ordering an easy jig. Did not want to make any mistakes and end up ordering another. Don’t remember where I order the one jig from
Did not see any of frosting on the boolets if there was any very mild
50/50 range lead/ww, with out sending it off for analysis of the alloy, the best I can do telling y’all what it is. Run a pid on the pot.
Forum: Casting Equipment
Been there, look for a one piece style. I have a 12ct square mini cake.
Dusty, I just read in to things too much,
The heat I have to cast at with it gets me. Lee 255 452 same design mold took half the time to get to get good boolets, mainly used to cast sabot loads...
Very mild abrasive polish and a brush. Did not see any burrs after smoked the mold, did not see olds left. May go on and give that mold another cleaning. A pre heat on the pot will heat it up, spur...
Hotter then I thought they should. I have a good number of older designs and newer design. I was running the mold as hot as the lee improved mini
Once it got really hot, spur cut easily by hand ( welding gloves on while casting). I have a couple I could try. May go on and give the mold another cleaning but maybe casting as hot as I was may be...
I been using only lee molds since I started casting. I was casting with the lee 358-158 double (going to load for 350 legend). New mold, could not figure out why the spur plate would not cut, could...
Forum: Special Projects
I bought an grab bag from a dealer, there was a ar 9 Lower. Spent two hours “drill press” milling one of the mag support to fit the mag release. Very slow and took my time. Finished with a router....
Forum: Gas Checks
1) is similar to what I am working on now but with 1/8 in plates bolted together
2) made one like it, not too sure where it is right now. Got divorced a few years ago a put a lot of stuff in...
Forum: Gas Checks
Thanks, going to work on it slowly. Have to make punches for it. Soon as I figure out how to post pictures from my phone, I post an picture
Forum: Gas Checks
First off, I am setting up to load for the 350 legend. Kinda stole an idea for a punch style but used two 1/8 in plated bolted together with washers to give space to slide aluminum thru (soda cans...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |