I just saw this post. The pusher business is my full time business now, rather than a hobby. Indeed the designs have made progress, though the operating principle remains the same. If you have an...
Type: Posts; User: epj
Forum: Gunsmithing Tips & Tricks
I just saw this post. The pusher business is my full time business now, rather than a hobby. Indeed the designs have made progress, though the operating principle remains the same. If you have an...
Forum: Cast Boolits
I have tried 9mm lead with Tightgroup and it did not work out all that well. I have used Clays, Universal, (2 different powders) AA5, and 231 with much better results.
Forum: Cast Boolits
My 6 hole Lee molds seem to like to be real near 800* to cast well.
Forum: Cast Boolits
.007 is probably too much to size. If you don't find an obvious problem, I'd send them back and get another set.
Forum: Cast Boolits
Some of the small toaster ovens have a convect setting. Check thrift stores.
Forum: Cast Boolits
Been casting 9mm almost exclusively for several months. Had to quit my trunciated cone bullet that I like real well in favor of a round nose to get it to feed 100% in a new 1911.
Forum: Cast Boolits
I'm too frugal to cast heavy for caliber. In addition, I'm not what I would call recoil sensitive, never have been. As I get older and my joints get worse, I appreciate a lighter boolit and in some...
Forum: Cast Boolits
Might try a little extra tin. The WW+ range scrap should usually be softer than straight ww unless you are digging out a lot of cast boolits made from lino.
Forum: Cast Boolits
Be carefull to clean out and fragments of steel wool. They rust like crazy.
Forum: Cast Boolits
I store lubed boolits in plastic coffee cans in the basement. It stays cool but never cold.
Forum: Boolit Lube !
I assume you are refering to the BAC. It's just a tad sticky. Not near as bad as beeswax/alox. If you can keep from getting it all over the boolit when lubing, cleanup is easy. That's why, however, I...
Forum: Boolit Lube !
If you don't have a heater, the BAC works real well. I prefer the Carnuba Red, but it takes a heater.
Forum: Cast Boolits
I use a number of Lee molds and have found that in general I need to cast a lot hotter than with steel molds. When I have been casting really good consistant boolits I find the melt temp to be close...
Forum: Cast Boolits
A 1911 in .45 would work well. I also have a gen3 S&W mod 4566 in .45 that will feed anything. It is super tough, accurate, and used examples can be had for $4-500; a lot less than a mid priced 1911.
Forum: Cast Boolits
Is this because the FCD post sizes the boolit too small?
Forum: Cast Boolits
The alloy is WCWW with a pinch of lino thrown in. The leading I experience is occassional and very minimal. It does not affect the gun's performance. Once in a while, when cleaning, I see a flake of...
Forum: Cast Boolits
I have used the Lee 120 TC lubed with Carnuba Red in a variety of guns with minimal leading. Most of my leading is in the throat. I keep my velocity at around 1000-1050 fps.
Forum: Cast Boolits
I had a similar issue using Tightgroup with water cooled WW. Couldn't get through a magazine without tumbling. I changed to Clays, which is a fast powder but apparently burns cooler. Little or no...
Forum: Cast Boolits
Use the styrofoam from an egg carton instead of a meat tray. It is thinner. I use this for several different boolits and it works great.
Forum: Cast Boolits
Been loading the Lee 9mm 120 gr. boolit for several years with an OAL of 1.10. I got this OAL from looking at a similar shape and weight boolit in the Lyman manual. Works fine in all the 9mm...
Forum: Cast Boolits
Are you sure they were regular primers and not "benchrest"?
Forum: Cast Boolits
Used to cast for a Carcano, bout 40+ years back. I found the boolits needed to be very hard. Something about gain twist rifling and the softer boolits not gripping well. YMMV.
Forum: Cast Boolits
I've never had anything that looked quite like that stuff. I do have a certain amount of shiney stuff in the dross that is probably tin I need to get stirred in better.
Your boolit looks like the...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |