Search:

Glad to see you posting again . The radius cutter looks great and of quality. I will be following your 30 cal die making. My die making has slowed down till my right arm recovers form severe...

try STM in the top of page adds for ss pins

I don't have a blackout rifle or a piece of brass, Someone who has both a blackout an 223 can answer this simple question "can a empty blackout casing enter a 223 chamber" The photo looks like the...

Cane Man
buy once cry once. here is a lathe that will take you thru die work to rebarreling,chambering, and other gunsmithing work. seems pricey but more than half the price is in tooling....

300savage
used to do a lot of business with Bill and Dave Christsan bros. They operated the Southern clay products
from your city. maybe before your time
Larry

http://www.corbins.com/rfjm.htm

1900 pennys for 9600 checks = 0.197 ct. ea math.

Customcutter: If you have a Fastenal store near you check for 01 or w1, they carry a few sizes.

Customcutter: I am certain you are using the proper tap, but there are starter taps and bottoming taps and the latter will not start under normal proceedures Just a thought.

Customcutter; Cane man has lead you into the lapping, I orded some leather polishing cones to use with the diamond grits for final finish. I have not had the chance to try them yet. I ordered...

You can use your existing reamer and modify it to the new specs. hone or grind from top to reduce diameter, nothing to lose.
You have a relief on the back of a 4 flute reamer .why not on the D...

79415[ATTACH=CONFIG]79416[/ATTACH)


On the cutting edge of the reamer you will see a shiney edge all along the reamer that is the relief, on the back side where it looks black is the relief ...

Customcutter Everyone has an opinion and I have mine, Do not grind the D reamer larger than half, one thousands under is best. an exaggatered example would be only 1/4 diameter removed and only...

Customcutter I mentioned glueing a 52 hp to the end of your sized shank, then see if your ojive setup will trace the outline, adjust or change until it will.

When you get the shank to size and start the radius, I have used superglue to glue a serria 52 hp to end and held in place with carriage till glue is thourghly set, Then you can adj the grinder to...

I use a mill and rotary index, and 120 deg spacing.
For the ogive I use a home made radius grinder with repeatable settings.
KTN uses the mill head set at an angle to shapen the point, which is...

Hello KTN
I havent seen your posts for a while, but I follow them.
I also find the four flute difficult to manuf. and went to the three flute. Made one 308 three flute and looks and sharpens...

The pic is a 4 flute reamer. they have problems not associated to a D reamer.
The diamater is .220 the flute is cut to a depth of .080 ..
This depth leaves some stength to the flute but the...

Sprinkintime
Does Enco or McMaster Carr supply 06 Tool Steel?

06 tool steel
http://www.peerlesssteel.com/productlist/toolsteel/

The holes are to set the ojive, the present setting is a 6 ojive, two holes from the top end is approx 9 ojive.
A different size wheel will change the ojive. It is adjusted for wear as you use...

73933

rotozip tool used for grinder, not a clear picture but u can get the idea of layout for adj ogives

I searched Master Carr tool steels and did not find 06 graph mo listed. Where did I miss it?

6849068491

The radius grinder is a rotozip tool
with a 1 1/2 inch wheel and run at the 20000 rpm, higher leads to vibration. It is locked to make the straight grinding and unlocked to use as a...

68430