Search:

I use this boolit in my side hammer muzzle loader and the gose through the deer , that the last one I got it went from the chest to the butt out. Took out the front shoulder and hind leg all on the...

When you use military brass it is thicker then regular brass. The data will be different then the regular brass .Also did you slug your barrel ? Because the size you stated is on the small size for...

Here in Iowa you get no notice and it is Constitution carry . There is more places you can go with a permit, then without one in the state, also it makes it easier to buy a gun in the state. Also do...

I use ground walnut to clean my brass before I size and deprimed them. After I do that then I use the ground up corn cob to take the case lube off and they are more shine on them, before that I just...

I use a hand roller that is use for round balls for ball and patch. I use it on my buckshot and takes care of it all . Some years ago I did a test with shooting 00 buck shot in a 410 . First test...

I know each mold have its own way to cast and once you find out how it will work for you, then you good to go .

This what I was going to say , if one dose not think so look at your calendar and tell us what is the last day of the week . And what is the first day of the week . I do not worship the sun . The...

I use it in 10 ga beside some handgun and rifle loads

Thanks for the heads up , when I get the funds thinking of get some of them to use. Yes for you to say about being a vendor on here then it will be easier to get in contact with him.

Go to the farm fleet store and get the cork sheet that you use to make gaskets, I use the 1/8" thick on , I let a friend use my cutters and told him to use the cork I stated because he needed a...

This is a good tip on use of a fired case to see about the bullet. Thanks

I have that mold and size it to .310 and works for me .

I make my own NRA Lube with ATF and make it as soft as I want it to be by how much you put of one thing. You need to test to see how much of it . That is ATF . I use the heater at times but most of...

What I did is buy the gasket hole punches from Snap on Tool , That is all I use and and a life time warrantee . There is a O ring that you can get in any farm fleet store when the one is worn out....

This is what I done also . Works for me . I got the idea off the internet. I think it was off of this site.

It is best to get the tool that is stated . Some makers of hulls mainly the ones made in Europe have different size primer pockets. Not like the ones made in the US , it is best to measure the pocket...

Not to get off the subject on pistol round , Rem make a pump for 30-06 in the model 7600. I got one and love it .It dose have a mag for it . For what is stated if there is one company put more...

This is good to know .

Those 120's can be a pain to try to set. For how small they are , I am doing good setting the 110's. for how it is for me. I use my setting tool mainly now. Also the one I said about setting the...

Here is about to make your own , need (2) 1"x1/4"x24" flat steel . then on each you do the following . 5/16" hole on center 7 1/4" down . as for the notch 5/8" down on the same end you start...

I will have to check on that . I will let you know . I know it is 1" flat stock and I think 1/4" thick. Just to let you know . I try the caulking gun setter on my 330's and it did not last long. I...

Do you have the setting tool for 220 and 330 's? If so see if that will help you to set them . I have some I had a hard time to set and that is what I used. It works for me.

I just melt the ones that end up in rejects or ones I had to pull, all gose in a tub to be melted down . Otherwise I only cast what I need . Save the alloy for when I need more for what ever it is...

You give some good points , I shoot 147 gr FN in my semi auto and feeds well. But like you said need to watch what ones will feed for your gun.

Good advice . it is best to do it with a dummy round to test this to keep it safe.