Hi Folks,
Thanks for your previous support but Im getting older and need to do more fishing.
Im putting it up for sale.
What I have is a V&O #10 punch press, which is double action...in other...
Type: Posts; User: wind power
Forum: Gas Checks
Hi Folks,
Thanks for your previous support but Im getting older and need to do more fishing.
Im putting it up for sale.
What I have is a V&O #10 punch press, which is double action...in other...
Hi I apologize about the delay...I dont get by here much....yes I still have the Hornet reamer, shoot me a PM.
All the best!
Gavin
Forum: Gas Checks
I sell the heck out of .30 caliber gas checks
Check me out at www.Bulletgaschecks.com
Probably the best prices out there, if not I will meet or beat if you need a quote
I have them in Aluminum...
I have a scaled version of the Stevens 44-1/2 falling block in Hornet, I had to cut the chamber myself with a clymer reamer when I re-barreled to the Hornet.
I have seen them in Winchester Low...
Forum: Gas Checks
This is Free shipping within the US[smilie=1:
If for some reason you dont like them, just return and I will gladly refund your money.
www.bulletgaschecks.com
.30 cal Aluminum, 16.50 Copper,...
Forum: Gas Checks
Hi Huntinlever,
If you're interested, I make gas checks and will gladly take them back if they dont work out for you and shipping to the customer is always free.
Im at www.Bulletgaschecks.com
...
Forum: Gas Checks
Thanks JonB, the equipment I use came out of an armory and the tooling I make myself, the tolerances have to be close for the speeds I run, which also requires the punch press to be a very rigid...
Forum: Gas Checks
Hi Folks,
Yes ebay dropped a lot of folks, but Im now a Vendor Sponsor here and still offer the same low prices on gas checks...Ebay now cant gouge me for fees on the gas checks, so in the end they...
Forum: Gas Checks
Ebay blew me up too, as far as wanting to back, I would rather not, they are expensive and the fees I was getting hammered on, will only go to the customer as a further discount on my gas checks.
I...
Forum: Gas Checks
Hi Folks,
They are on ebay and its always free shipping; by building my own tooling I can control the tolerances better and modify them easier to crimp better.
Im a reloader and shooter too and...
Forum: Gas Checks
Hi Slim,
I have to buy the metal in the hundreds of pounds often approaching 1500 lbs sometimes and have to bang them out fast and accurately too, to sell at that price. I make my own tooling and...
Ok I did a few things today.....
After slugging the clean barrel the slug measured .4505-.4510
I also used an inertia bullet puller (Hammer type) and mic a loaded crimped bullet, that bullet mic...
Hi Thanks for the info, I will drop the powder charge and pull a bullet to see what I have on the OD.
I will also slug the bore and check what the dimensions are there too.
I will water quench...
Hi Lee,
Thanks for your reply....I see it is a hot load...too hot in fact...I ahve a Lyman manual which lists it a bit close to my 5.6 load of red dot, but it is at 5.3 grains max...I will reduce...
Hi Folks first time poster.
I'm having a dilemma with a 45acp round I have worked up.
The bullet is 200 grain (actually weighs in at 215 grains) and is a LEE double cavity # 90234. (It is flat nose...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |