Search:

https://castboolits.gunloads.com/showthread.php?284586-Lee-358-150-1R-load-suggestions-38-special

Here a start for you

Mr.O

There new site is down undoubtedly.



MR O

yea got the same email


MR O

Go to hogdon web site then data tab and read about using H-4895 in reduced rifle loads it will tell you what you need to know


MR O

i have never used the stuff but you made the curiosity come out in me,here's a link i found go there at your own risk

MR"O"

...

I do not do a lot of posting here but i do read a lot here so to answer your question estimating velocity this is what i use don't remember where i got it but it does work some what close for...

See if you can get the new 2015 hodgdon reloading magazine it has a good article on the new imr powders and to answer you question they are not made for shotguns




MR O

sounds like you have got it reduced to much if you are try to go subsonic you need to try a little fast powder that will completely burn that's what i had to do, change powders are bump the load up....

I am using 12.5 IMR 4227 with tula Small Rifle Primers (the tula seam to be hotter than CCI SRP) for the little bator and getting 1" groups at 50 yards, on paper about 2000 fps have not chrony...

So who has pacemaker first hand knowledge? I have a top of the line medtronics pace since June of 2012 i had Afib before then which caused blood clots to settle in my lower body manly my gut and...

I am doing the same thing you are, i pick up a bull barreled Rossi 223 1/12 twist about 2 month ago so i can shot on the cheap, i have a good load using the Bater mold that drops at 50 GR not 55GR...

try this link it may help you decide what to do, but my two cents i would go with HS6 its a slower powder like blue dot.


http://www.adi-powders.com.au/handloaders/equivalents.asp


MR O

Here try this from Grumpa, its for a 45acp may give you an idea, i tried something similar in my 45acp and it work good if your with in 5 feet of what your shooting makes rather large pattern 2'x2'...

This is were i found mine gauges good luck


http://www.okiegauges.com/



MR. O

far sure look at e-bay just pick up a Lyman 225462 single cav for $40 i have been watching a while for it good luck



MR. "O"

I have never seen them and i to had to Google them they look like they would work good as long as you push on the top of the safe are shelf that is nailed down so it would not move ,my shelf's move...

I call the fruit horse apples and we called it a bodark tree never heard it called a Osage orange you learn something new every day ,do know its hard wood had to cut some down one time burn up a...

if your close to Kerrville go by Gibson on Texas 27 going out of town a mile are so they have a little of everything, nagler is the place if you looking for something odd everything else is to high...

Good old Bexar county (for all you newbies to Texas that pronounce BEAR) were they serve there Bologna in a tortilla.




MR O

if its shorter than 18 inch it is illegal if so throw the barrel in the back of your truck the butt in the front floor board and don't act stupid on the way home and you will be OK. People in Texas...

You have a sizing problem not a powder problem (you load is the same-thing i shoot but in a different gun) if the load is to light then you would have failure to eject and failure to feed (stove...

follow the link maybe you can identified it and see what it is for sure but by look at the pic it is a m91 and if that's correct it been in country along time


...

i was turned down twice even had doctors say i was disabled i got a lawyer, you need him get all the correct paper work for you that they require,because they will not do it for you are tell you what...

I don't know much about the muzzle breaks i don't use any on the Mosins but for a light load and i laugh every time i pull the trigger is a 93 GR. 314 tumble lube lee SWC over 5 GR titgroup my target...

I second the moth balls i know they work on squirrels i used it after they cost me a $1000 in a rewiring job on my tundra



MR O