I am building a 357/38 rimless, anybody got information on this cartridge.
I essence its a 223 case cut down to 357 length; re sized...
Any information would be helpful.
Regards
Type: Posts; User: Mozz
Forum: Special Projects
I am building a 357/38 rimless, anybody got information on this cartridge.
I essence its a 223 case cut down to 357 length; re sized...
Any information would be helpful.
Regards
Forum: Case Forming / Re-forming
I am building a 375/38 rimless, anybody got information on this cartridge.
I essence its a 223 case cut down to 357 length; re sized...
Any information would be helpful.
Regards
Forum: Swaging
I take your point thank you for your reply...
Forum: The Star Equipment Corner
This has made me think i should sell my star sizer...
Forum: Swaging
Guys im looking for a little advise here.
I have a full set of BT Snipers 223 bullet swagging dies include, mold and ejector which I am not using. I would like to rebuild my reloading bench and...
Forum: Casting Equipment
Many years ago (on internet), I had the larger machine with four molds, the element went on that, being in the UK i had real issues sourcing an element. In the end i had one made up that i retro...
Forum: Swaging
I've just commissioned a copper bullet design. So I can judge whether its worth getting them made to sell on or just for me to hunt with.
Once i get a price i will let you know.
Forum: GB RUN BY Wasalmonslayer
Could i order 2 Cavity Brass solid, machines mold, 155bb. DPM308 dot @gmail dot com
Forum: Gunsmithing Tips & Tricks
Thank you very much guys, very informative.
Forum: Gunsmithing Tips & Tricks
Guys ive got the opertunity to buy a bare Armalight AR10 lower, its used and that amounts its been been used is unknow.
My question is will the modern day parts fit?
Regards
David
Thank you Guys. Some great suggestions and advice.
Can anybody recormend a 223 mold. I'm looking to use as a pactice round, 100 metes and less. For use in a AR15 straight pull.
Forum: Swaging
Thank you i didn't think of that... I will let you know.
Forum: Swaging
I have made some 62 grain RF bullets and loaded them with 24.3 grains of N135 and traveling aroung 2,850 ftps. I use the Serria reloading manual as a refferance which has neaver let me down.
I...
Forum: Coatings and Alternatives
Trevor are you pre-heating your bullets to ensure they are dried fully?
Forum: Coatings and Alternatives
Ah, that's clearer thank you. I was using a plain non coated bullet. I will get a infrared thermometer as advised.
Once again thank you for your help and support guys.
Mozz
Forum: Coatings and Alternatives
My mistake i've coated with a 10gms to 100mils mix, as I have only been coating 2kg of bullets at a time.
Forum: Coatings and Alternatives
So just to be clear I am sure that the coated cast bullets are reaching temperature, the oven is controlled by a PID and the thermal couple has a bullet screwed on the end of it. Once the oven has...
Forum: GB RUN BY Wasalmonslayer
Can I have the 155 SOLID in bevel base, in a machine mold - ive spoken to the guy.
dpm308 at gmail dot com
Forum: Coatings and Alternatives
Thanks for your reply. Its powder Hi-Tek, it must not have dried properly, because its defiantly getting more than 2 minutes at 180C. I coated some more this time with Red Copper which did pass both...
Forum: Coatings and Alternatives
OK what am I doing wrong,
2kg of bullets, 10grams (CAR) mixed with 100 mils of Acetone.
Baked at 200 for 13 minutes. Oven has a PID and Fan and both seem to work well. Covering looks good.
...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |