Search:

Hi Guys,

It was the only game I watched this is year! Same reasons as mentioned in other posts!

Half time was another bad joke on music and intelligence! Some people were paying up to $1800...

Hello All,

Would any of you know if a1905 Brazilian Mauser bayonet will fit correctly on a WW-2 German 98 K rifle ?

Thanks for any help,
broom

Hi All,

I saw two blown firearms years ago. One was a 45-70 trapdoor fired with hot modern rifle loads, BANG heard the guy yell -I turned & saw the barrel sailing down range. He caught some case...

Hi Posters,

I was told by a few old WW-2 Marines that the old WW-1 16 inch bayonet was favored by the American troops. Especially before the Marines got the M1 Garand in quantity. Eight fast...

Hi Handloader109 ,

Two choices for you! Assuming both cases fit & eject from your rifle..

If you know someone with a small metal cutting lathe they can neatly put the correct angle on the...

Hi atr,

I'm told my RB is a later model 1910 as it has a band front sight. I'll try your loads soon & get back to you.
If you have the time, can you post a picture or two of your fired cases? It...

Hi atr,

Did you use standard 7 mm & fire form it with this load?

Did you take the extra step to resize it to 30 cal. & reduce back to 7mm to better fill in the overbore pre SAMMI chamber...

Hi PBSmith,

It's a good group here! Please send a small donation to each of the nice guys, that replied to you question!:grin:

If you have all the original directions for your scope many of...

Hi Fellows,

Thanks, I thought it was me! Sadly my computer skills are very poor.

broom LB check your PM's ---I may be able to help you out.

Hi All,

Is anyone having a problem getting on the CMP forum board? The screen goes white, if I try to open any post?
I'll stop by later to see if anyone replied.

Thanks for any help,
broom

Hi All,

Thanks for the reply's I don't thiunk they will be for sale.

Good Luck & GOOD HEALTH to all,
broom

Hi Fellows,

I have access to three receivers two are WW-1 #over 1,000,000 & a 03 A3.
The owner has no idea of their history, they were on a high shelf in the basement of his house.
Before I...

Works on my old computer!

All your bases are covered!

broom

Hi All,

A well respected member of another shooting board mentioned that his pal Cast 75 gr zinc HP and it went 3900 FPS and made a clean hole! ------ I don't know what distance.------

I have...

Hi All,

I have used their Match Rifle powder for 223. 308 &30-06 using jacked bullets. Shoots clean & as well as well as the more expensive powders.
Their published data at the site is limited....

Hi All,

I was hoping someone had a better idea!;-) I have been doing it just like all of you for years! It's just a little annoying to look at each case. YES! it is a built in quality check for...

Hi Bazoo,

That's a good thought!
I was thinking about some type of quick bulk guide. To lining up say 50 cases.
So I can just pick out the small cases. The only idea I came up with was a...

Hi All,

Small primer 45 brass is a problem for me![smilie=b: There has to be a better way to separate the brass, then sorting through ever case as it comes out of the media separator!

Any...

Hi All,

A good thread! Lots of good memory's!
My older cousins had a old Winchester 22 single shot their dad gave them.

The family rule was "If you could pull the bolt knob back, you were...

Hi Sir,

You should contact the maker of the shotgun ! I have been around shotguns for years & never saw one like that.

"IF" it was shot with steel shot. The barrel might fail depending on...

Thanks for the replys I'll pass them on!

Best wishs to all of you,
broomhandle

Hi Posters,

Thanks for the reply's!

I did not know about pinning the floor plate, it makes sense since the Greeks had 03 A3's too! It was a small, but ugly civil war with the Greek Communist...

Hi Ladies & Gentleman,

A pal just bought a nice Springfield 1903 rifle made in 1917. It's marked as a import on the barrel in small letters Century arms Vt. It has a later 03 stock with no...

Hi Fellows,

jsizemore was the motor made in America or China? With a little luck you might fine new bronze bearings at one of the bearing places on line. - Granger for one!

I don't recall the...

Hi Fellow Re-loaders,

My unit has been in use for about 35 years! That's a good run for any product!
In case you ever have a bearing problem with your Dillon older style vibrator, it's a easy fix...