Search:

Reminds me of trip to Fl, son wanted to fish off the bridge. Got a blowfish and then an eel. Had to get the side cutters to cut the stainless leader. He wouldn't get near it. Now his company says he...

Grind off 50 thous of the bottom of the die (not shell holder - they are HARD). Screw down the die extra 1/2 turn and size a case. If the bolt closes with little resistance, that's good for YOUR...

Spank it.

Yup, should mark the expanders. Mine are old style stepped, they work. Nose sizer rig? Not so much. Never got a mold from him.

Old or BAD brass! Neck is filthy. IF purchased lately send to Rem, otherwise, just toss the cases. Annealing probably won't fix.

An old teacher told me the use of the 1911 45 (WWII Pacific) was predominantly to kill Warf rats. They couldn't get tommy guns for dock patrol.

Nope, not needed. BLL actually degrades PC. Tested on rifle bullets.

Dang, none for me to shoot. Was watching an (pro) Aussie shoot them @200 yds with sub 308W. Interesting (and he is a good shot) sub 308 220 gr has LESS energy and poorer traj than 300 BO 135gr...

Trigger, not sure what you are asking. yes sulfur will combine ( form a molecule) with zinc to remove zinc. Yes, remaining sulfur will stay in the lead. I did cast for 40sw, pure & zinc <1%, alloy...

Solubility of sufur in lead is quite high at higher temps, decreases at lower temps. Correct, it is held in the lead lattice but does NOT form a new molecule. Same with most added elements in lead. ...

I've used red dot in BO, 30/30 for plinking. Haven't seen the position sensitivity yet. I use a single shot CVA so random 'position' of the rnd when loaded. But BO is a small case. I did notice the...

The NOE has an edge to do the sizing (at least the original), basically a tapered hole. Doesn't work well for me. Using nose sizer in the body, ya can't pull the bullet out easy (and held in with a...

.are undersized boolits that inaccurate? Yup. They get 'damaged' in the bore and don't fly right.

IIRC they weren't that effective. Too many people involved in shooting and not that accurate. Mostly fear factor. The really big one was used to destroy an ammo dump underground. Barrel life was...

IIRC NOE 30/30 expander is not long enough to expand all the neck. I use a lyman 311 M expander, it's longer. The stepped expanders give a large flare to the mouth and the STOP step is sometimes hard...

In the real old days, heater core was in a separate box, inside on the firewall. Early fords had the heater box under the hood.

Especially hardcast heads. Call them knotheads? I consider it the alloy commercial cast Co get from the foundry.

Get the alloy calculator, figure what you have BHN-wise. YOu probably need something like 10 or 11 for the 9mm. WD won't work from the mold, drop in cold water after cooking the PC for 1/2 hr.

yes, but you might be over gassed. Different barrel makers use different sized gas ports. How will you know? brass goes to the next county! Solve that problem with an adjustable gas block.

Fill one hole at a time (alternating) until the sprue/mold gets completely up to temp. Use a wood mallet/stick to 'break' the sprue until the mold is up to temp, then you can open by gloved hand....

If the plunger doesn't push in, order a new shaft from NAA and dremel the old one off. The spring just holds the pin out, ball fits in detent in pin and barrel. Or try the 4-6 thous feeler gauge -...

Sulfur will harden bullets. Probably not what you want for balls. And it never stops stinking.

Brake cleaner, front and back of cylinder pin. Detent spring may be rusted but everything else is SS.

No, you can't see through the brush with IR. Had a hog come in trough the trees, stopped at the edge of the field then turned into the brush. I wasn't fast enough. I like the AGM Rattler V2 640....

Spray painter's mask should work but what about the eyes? Googles too.