Fraid I just missed gun is dead on still...
https://uploads.tapatalk-cdn.com/20171021/296f42f1802c4506846a1a756b1fc17d.jpg
Sent from my SM-G900V using Tapatalk
Type: Posts; User: aarolar
Forum: Muzzleloading.
Fraid I just missed gun is dead on still...
https://uploads.tapatalk-cdn.com/20171021/296f42f1802c4506846a1a756b1fc17d.jpg
Sent from my SM-G900V using Tapatalk
Forum: Muzzleloading.
Well the gun went boom but I missed 3 absolutely gimme shots on squrriel gonna check my sights when I get home something seems off.
Sent from my SM-G900V using Tapatalk
Forum: Muzzleloading.
Too late now I'm leaving it until after tomorrow's hunt. I did swab it with a dry patch both sides then run a patch lightly coated in my lube down it.
Sent from my SM-G900V using Tapatalk
Forum: Lead and Lead Alloys
I was careful to remove all the solder joints and use just the pipe.
Sent from my SM-G900V using Tapatalk
Forum: Muzzleloading.
Using my own rendered pig lard, should I swab with that or something else alls else I have is bore butter which I've purty near swarn off.
Sent from my SM-G900V using Tapatalk
Forum: Lead and Lead Alloys
I just sorta confirmed my suspicion, tested a piece of pipe without heating it at all and it tested .040. Can I anneal it back and if so what temp should I use?
Sent from my SM-G900V using Tapatalk
Forum: Muzzleloading.
Goex
Sent from my SM-G900V using Tapatalk
Forum: Lead and Lead Alloys
Will pure cast lead ever be as soft as swaged? I have a homemade cabine tree style tester and swaged hornady round balls test at .035-.040 my pure cast lead balls test more around .060, I have tried...
Forum: Muzzleloading.
I discharged my hawken this afternoon, took out a nasty coyote, reloaded and finished my hunt. Didn't see any deer I'm planning on going again in the morning, should I pull the load and clean the gun...
Forum: Lead and Lead Alloys
Will this make soft lead for muzzloader bullets? I know the pipe is but I'm not sure what the joint is made from.
https://uploads.tapatalk-cdn.com/20171017/60eec6700c32a825b502f07ed66cac6b.jpg
...
Forum: Muzzleloading.
Enjoyed this story can't wait till my kid is old enough to spend time with me.
Sent from my SM-G900V using Tapatalk
Forum: Completed Deals
Looking to buy some pure lead for lead balls.
Sent from my SM-G900V using Tapatalk
Forum: Muzzleloading.
Yes this is with my cast balls and hornady swaged balls.
Sent from my SM-G900V using Tapatalk
Forum: Our Town
This story describes perfectly why I'm super peculiar about who I hunt with, sorry to hear about your ruined hunt.
Sent from my SM-G900V using Tapatalk
Forum: Hunting with CB's
Had a good hunt this afternoon with my 7 year old puppy. First time ever using a 50 cal on tree rats as well. What a hoot watching them fly 6 feet up in the air back flipping.
...
Forum: Muzzleloading.
I always swab between every shot. I went out shooting this morning and had a revilation, started using spit patches and it made everything sooo much smoother it was great. I had been previously using...
Forum: Muzzleloading.
I have a Renegade that I enjoy shooting but I neglect it because I have an issue with the ball/patch relationship. I am using a
.490 ball and want to use a .015 patch or so which gives me the best...
Forum: Factory Rifles
Ok this really peaks my interest where can I find a barrel chambered in this round? A quick internet search turns up naught.
Sent from my SM-G900V using Tapatalk
Forum: Factory Rifles
Update here I've settled on my hunting load for the year. It's going to be with J words although I've not given up on lead hopefully I'll get it there for next year I didn't have alot of time with my...
Forum: Factory Rifles
I want to build an AR upper to use for deer hunting and target shooting mainly for my missus to use but just to get some use out of my AR. Should I go with 6.8 SPC, 6.5 Grendel or 300 BLK and why?...
Forum: Our Town
Clear your PMs you're all full up! :) @Texas by God
Sent from my SM-G900V using Tapatalk
I had a ND once inside the house with a 22lr and it was unbelievably loud, I can only imagine how loud it would ever be if I had to use the .357 in my nightstand on an intruder.
Sent from my...
Forum: Factory Rifles
Appears to be approximately .012 thick.
Sent from my SM-G900V using Tapatalk
Forum: Factory Rifles
Finally got around to the pound cast and here is what I got could someone please help me interpret it. Can't accurately measure bore size due to three groove rifling.
...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |