I'm casting the 95g SWC from Saeco for my custom 32 magnum Single Six. They actually come out weighing around 98 grains. It shoots these bullets extremely accurate from very low velocities(600-700...
Type: Posts; User: Jerry Lester
Forum: Hunting with CB's
I'm casting the 95g SWC from Saeco for my custom 32 magnum Single Six. They actually come out weighing around 98 grains. It shoots these bullets extremely accurate from very low velocities(600-700...
Forum: Cast Boolits
I haven't posted for a while, and really not much at all here on this site. What I have done is read a lot, and experiment with a lot of the things I've seen ya'll discuss on here.
I just got my...
Forum: Casting Equipment
I'm not using a heater:neutral:. Should I be? Maybe that's the problem?
I'm using Javalina lube. This lube is very soft at room temperature. I can easily mash a chunk between my fingers. It's 50%...
Forum: Casting Equipment
My casting has come a very long ways in the last year, and I've learned a wealth of stuff from here, and by trial, and error(mostly here[smilie=1: ).
I've been sizing my 32 bullets with a set-up I...
Forum: Cast Boolits
I've been saving my loose change for the last few months to buy a sizing press, and all the other goodies to size my bullets, plus "hopefully", I'll have enough for a good 357 mould to boot. I'm...
Forum: Cast Boolits
Hollow base WC's like the Hornady's turned backwards, loaded in 38 cases, and fired from a rifle do tremendous damage to groundhogs innerds. I haven't tried them on a coyote, but up to 50 yards it...
Forum: Cast Boolits
Thanks fellows. I tend to be a little on the obsessive side when it comes to this kind of thing. I'm thrilled that I'm getting the accuracy I am already. I just thought maybe holding the variance...
Forum: Cast Boolits
I understand that this is a relative question depending on the degree of accuracy that is expected from a given gun/bullet/combo. Even with plinking loads though, I tend to be obsessive in trying for...
Forum: Cast Boolits
I'm very new to casting, so my experience is very limited. The only casting I've done is for my 32 magnum. I'm casting the Saeco 95g SWC, and this bullet is amazingly accurate. It also has a wide...
Forum: Cast Boolits
In a few weeks when funds permit, I'm going to buy a lube-sizer. I've tried the LEE, and was not too impressed to say the least. It worked but was very messy, and somewhat tempermental to use.
...
Forum: Cast Boolits
Cbrick,
If those bullets are expanding that violently in just water, they'll likely fragment on impact with flesh or clothing.
I've tested a "LOT" of bullet designs in dozens of mediums ranging...
Thanks for the replies.
The lead smearing is my fault for getting in too big a hurry. I know better than to cut the sprue too quick, but you know how it is sometimes[smilie=1: .
The thing that...
I had a little bit of lead smear on my mould the other day under the sprue plate. After cleaning it off really good, I figured(in all my infinite wisdom[smilie=1: ) that if I tightened the plate a...
Forum: Cast Boolits
I'm shooting them from a custom 32 magnum Single Six. I try to keep shots at game within 50 yards, but I regularly practice with my revolvers at 100+ yards.
Forum: Cast Boolits
Interesting! Keep us posted on your results please...
Forum: Cast Boolits
I spent a while weighing my 32 magnum boolits last night. This 95g Saeco SWC mould is dropping them on average at around 97.5g which is fine with me.
My question is this...
I decided that + or...
Forum: Cast Boolits
Thanks for all the good input!
Looks like I'll be experimenting quite a bit with this stuff.
Forum: Cast Boolits
I've read quite a bit of contradicting info on exactly "how long" to wait before sizing a bullet. From what I've gathered, most casters say to wait a period of time, but the times I've read have...
Forum: Cast Boolits
If you start casting at say 700 degrees, and then change to say 800 or 900 degrees, would that change the weights of your bullets? I haven't tried it yet, but I'm figuring that at the very least, the...
Forum: Cast Boolits
I've been smelting my weights into usable mini-muffin ingots, and the other evening, I got to looking pretty closely at them. A lot of mine have a number 57 on them, but there are a lot of numbers...
Forum: Cast Boolits
Thanks for the info fellows. My bore slugged at exactly .310", and my throats are .312". I can chamber a .313" bullet, but have a hard time chambering the Hornady .314" 90g WC's unless they're flush...
Forum: Cast Boolits
Actually, I'm needing a .313" bullet. This Saeco .313" 95g mould is dropping bullets at around .315" so I have to size them down. I contacted Saeco, and he said that this .313" mould is "supposed" to...
Forum: Cast Boolits
First off, what hardness is pure wheel weight alloy? I realize that it likely varies, but "around" what hardness are they?
Second, my wife informed me that there just "might" be a nice Redding...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |