I have that same rifle and the Dan T mould for it. BACO makes the mould and mine drops @ 365 grains. The OP however stated he will only be shooting from 100_ 300 yds so there is no need for a mould...
Type: Posts; User: WKAYE
Forum: Single Shot Guns
I have that same rifle and the Dan T mould for it. BACO makes the mould and mine drops @ 365 grains. The OP however stated he will only be shooting from 100_ 300 yds so there is no need for a mould...
Forum: Single Shot Guns
Yes, I have one. I have other moulds besides the BACO and I size them @ .380 as well.
Forum: Group Buy Discussion
You've been asked to provide a drawing and have not. You expect people to give $113. for a mould with no idea of the sizes and if it may be useful to them ?
Forum: Single Shot Guns
My BACO .380-360 drops them @ .380 and I do not resize them.
Forum: Lead and Lead Alloys
Divedigger, see my post to Hairy Dawg. If your babbitt is marked "Genuine", you have the same alloy.
Forum: Lead and Lead Alloys
The answer to your question is cast into the center of that ingot. Search "Genuine" babbitt, also known as Nickel Genuine. I've used a bunch of it, treating as tin.
Forum: Group Buy Archives
Mine arrived today. Looks great. Thanks Miha.
Forum: Group Buy Archives
Bob,
I have a new email : kaye1(at)bellaliant(dot)net
Just in case this one goes ahead.
Thanks
Forum: Group Buy Archives
My 2 moulds and Lee sprue plates arrived this morning. The workmanship looks great. Thanks Joshua.
Forum: Group Buy Archives
Is this mould ever going to be cut ? Approaching 20 months now !
Forum: Group Buy Archives
Is it possible to get 5 of these plates with Std holes, shipped with the 2 -$55. moulds that I have ordered ? Just trying to save a little on shipping to Canada.
Forum: Group Buy Archives
Do you ship to Canada ? If so, how much ? I would like 2 GC moulds. One .312 and one .314.
Thanks.
Bad ***,
After seeing numerous posts of yours regarding the Pedersoli Highwall in 38/55, I just had to get one. Well now that I have it, I see that P Jones no longer makes the mould that you have....
Forum: Group Buy Archives
I'd take a .360, a .380, a.460, and a .510. I could use these yesterday!
Forum: Group Buy Archives
Mine arrived today. What a Masterpiece ! Thanks Miha and Bob.
Forum: Group Buy Archives
Bob, thanks for getting this off the ground. Please put me down for a 4 Cavity.
nkaye(at)nbnet(dot)nb(dot)ca
Forum: Group Buy Archives
Please remove me from the list. H&H traded off.
Thanks.
Forum: Group Buy Archives
Please put me down for a 2 cavity, with blank and HP pins.
nkaye(at)nbnet(dot)nb(dot)ca
Thanks.
Forum: Lead and Lead Alloys
It sounds like Imperial Babbitt to me.
Approx. 86% Tin, 7% Antimony, and 7% Copper.
Most of what I have found were in 4 lb. ingots.
Forum: Group Buy Results
Al,
Please put me down for a 2 cavity GC, .314 diameter.
Thanks
Forum: Group Buy Results
Mine arrived today. Unfortunately, the box had been broken open on a corner and some pieces are missing. There is only one Blank pin, and one Large HP pin. Both Small HP pins are there, however, so...
Forum: Group Buy Results
Please put me down for one mould with Small HP pins and a set of blank pins.
Thanks.
nkaye(@)nbnet(dot)nb(dot)ca
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |