Ballisti-cast Mark-II autocaster (6 mold setup) NV-Ballistics Speedcaster 42, and soon a brand new Magma Mark-8 bullet master.
Were you debating on an automated machine?
215483
Type: Posts; User: nh7792
Forum: Casting Equipment
Ballisti-cast Mark-II autocaster (6 mold setup) NV-Ballistics Speedcaster 42, and soon a brand new Magma Mark-8 bullet master.
Were you debating on an automated machine?
215483
Forum: CB Loads / Military Rifles
Just got my "Elvis" mold also, not sure when I'll be casting any, but curious about how they'll do in a semi-auto. My plan was for bolt action.
Forum: Reloading Equipment
Pulled it and flipped it before sanding it in hopes I wouldn't have to sand it.
Forum: CB Loads / Military Rifles
Nice to see the difference between GC and no GC with PC.
Forum: Coatings and Alternatives
Quick rinse in acetone will clean them off and get them ready, plus the acetone flashes off pretty quick. I didnt read all the comments, but recommend sizing after PC'ing the bullets, in some cases...
Forum: Cast Boolits
Not sure about the rest of the folks, but the hotplate was only used to heat up the mold while I got the pot filled and ready, then to keep the mold ready if I needed to walk away for a sec or to...
Forum: Cast Boolits
The 92/6/2 is your most common casting alloy, and most your commercial mold manufacturers (Lee, Lyman, RCBS) make their mold to the 92/6/2 specs. Used to be Lyman #2 was the go-to alloy, but that...
Forum: Cast Boolits
How much tin did you add to get the BHN form 8 to 14? Something's not adding up. As far as dull vs. shiny, that's mostly temp related.
Without a thermometer trying to guess the temp will be...
Forum: Factory Rifles
I have 3 that are in different levels of being able to shoot. 2 that just need to be zeroed in, and 1 that needs rings for the scope. One of the ready for zero rifles is almost 2 years old, and I...
Forum: Reloading Equipment
Possibly a gift card to cabelas? (Or whatever sporting store is close) If he is interested in reloading, the manual will help a lot, and a gift card may be easier for both so the kid can decide...
Forum: Coatings and Alternatives
And I thought my bakers pride commercial convection oven was a monster.
I agree with you 100%
Neighbor had one of the S&W 500 Mag revolvers, shot 5 rounds and put it back in the box. Lost $100 + the cost of ammo because he didn't like the kick and was scared to shoot...
Forum: Cast Boolits
Lots of seasoned casters on here. With the centuries of combined experience, shouldn't be any unanswerable questions in regards to casting and alloys
Forum: Lead and Lead Alloys
There is an awesome lead alloy calculator on here somewhere. You can adjust the amounts/percentages of the different alloys to get an almost dead on BHN.
The COWW I have ran across lately have...
Forum: Factory Rifles
A PSA .308 18" barrel AR-10. Bought it 2 months ago and havent even removed it from the box. Less chance of dust buildup in the box than the 5 sitting untouched and unshot in the safe.
I do have...
Forum: Deep Theological Discussion
I had an LDS bishop tell me years ago that you can only give what you can give, regardless of what people say or expect. He did go into great detail about what the $$ is used for and where it goes,...
Forum: Coatings and Alternatives
My experience with PC and Hi-Tek gas check/no gas check bullets showed me that if there is a shank for a check but no check on it, the accuracy suffered.
GC and PB bullets were "ok" group wise at...
Forum: Coatings and Alternatives
Thank you. It's nice to see another comment on what PC and Hi-Tek are. Many arguments over it being referred to as a "Jacket".
Forum: Cast Boolits
From day 1 of casting I was told to avoid Zinc like the plague. After reading and seeing the Youtube video, I may rethink that a bit.
Forum: Reloading Equipment
Dillon SS600. Been using mine for years. I would also recommend the Ballistic tools primer pocket go/no-go gauge. Found out the hard way a while back that each different headstamp swages a little...
Forum: Casting Equipment
Check with local scrap yards for Tin or 50/50 solder. I know a few local to me that are licensed to sell metals, some can just buy scrap but not resell it.
I had one for 2 years and loved it. Sold it because I never shot it. (more rifle shooting than pistol) Now I miss it and think I'll start looking around for another. :bigsmyl2:
Forum: Casting Equipment
It's posts like this that make me thankful to live in Utah. Arsenal and NOE are a 40 minute drive, and Accurate is in Salt Lake. (no pickup address, but shipping only takes a day or so)
Forum: Boolit Lube !
Carnuba wax will work to get it stiffer, but if money is tight old candles and crayons will do the trick also.
Forum: Boolit Lube !
I have made it and used it on a few calibers. Worked really well, but was sticky/tacky when loading. I added a bit of carnuba to the mix to try and harden it just a bit, worked "ok" on hardening...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |