Search:

Looking for a non-drill and tap scope mount for my 03' mk1 springfield rifle found 2 to be currently available. One of them on Amazon got bad reviews dont remember the manufacturer. The other...

Thanks to everyone for piping in, I am strongly leaning toward the Teslong to work with my Android phone

I have done some research here and on youtube concerning a borescope to work with my smart phone. I was thinking of ordering one with a lens small enough for .22 barrels, but am wondering it this...

Well I got the globe sight base off, it took repeated attempts at heating and soaking with Kroil oil but final victory came when I switched to a bigger hammer. I was using an 8oz ball peen and a...

I am prepping my Springfield for a barrel replacement. Current barrel has a Lyman globe sight on it I want to remove it to use on my new military barrel. I got the lateral thru pin out and was...

I have found myself with a good amount of this powder using it as a schuetzen load. Wondering if any of you folks have been using it as a cast bullet load for 30-06 or 308 win. Any suggestions would...

Wasn't sure where to post this, whats up with NOE looking at their catalog on .30 cal molds and it appears everything I was interested in was sold out. Is Swede planning on getting out of the mold...

Don't know if he is still in business but Aussie. Co. called CBE (cast bullet engineering) makes a really good heeled bullet for the 41' Swiss, I cast mine soft 25-1 and it shoots really well

Recently got my 41' swiss back out of the safe. I had a heeled bullet mold from the CBE in Australia sized .436 loaded up with 18grs. of 2400 it shot better than my 12 grs. Unique another load...

Same position as others trying to save my LR primers for competitive shoots. But I used LR mag primers in my springfield and found no difference with previous loadings 190 gr bullet with 19.5 grs....

I load for Shuetzen style shooting and bought 2lbs of AA#9 as recommended for use in my 32-20 CPA round. I found the stuff to be quite "peaky" I can get a load that is accurate but still detect...

I am down to my stash of LR Mag primers, I have several loads worked up for 30 cal. My go to powders are the usual 4759. 2400. 4227, etc. should I be looking at adjusting my loads when using Mag....

Thanks to all for the advice have not had a problem yet, didn't want to set myself up for a problem as time went on.

I haven't had a problem to date using rifle primers with rifle carts. and pistol with pistol carts. What does T/C recommend. Concerned that I may start to pierce pistol primers.

I have been a member for sometime could not recall password and forced to start as new member and lost my 30 and 30 requirements to post in buy and sell. My screen name was "rikkit" hope you can...

Thanks for the replies, let me explain as best I can on what going on. I am feeding the rounds 1 at a time, as I place a round into the magazine well I am pushing down on the rear of the round while...

I have a large ring mauser which I re-barreled from 8mm to 7mm-08, feeding bullets can be a pain sometimes using the controlled feed method. I want to know if the bolt on this rifle can be modified...

My 10 yr. old M-10 in 308 has a trigger which has become inconsistent. Looking around I see that Timney offers a replacement, and YouTube has videos of refining the existing trigger either through...

Anybody shooting this mold? I thought I had a 200yd. load worked out using 24 grs of 4895 and water quenching the ww bullets, starting to pickup a lot of sudden flyers. It could be me so I am...

I spent considerable time spinning my wheels with my 7-08 and finally found success with RCBS 7-168, I am water quenching the bullets for hardness and loading them with 24 grs. of H-4895. My intent...

I have a 98 Mauser action with a new barrel on it and would like to work up some loads using the Ly 168 gr. mould. Want to use it in our Cast Bullet commercial matches so 100 and 200 yard accurate...

I picked up a 98' action which is equipped with DST's, they are starting to give me problems. This set up has the small external adjustment screw between the triggers but it seems to not have any...

I am in need of a custom ".316" button for my RCBS sizing die. I am attempting to breathe new life into a P-14 Enfield by paper patching some bullets. Any body out there that can make one up for me?

EDG, it is my understanding that the turn around time depends on the make of the scope. My initial contact with Iron Sight was to get my Weaver T6 repaired. They indeed did quote a turn around for...

I just wanted to post a positive that I had with the people at "Iron Sight". My Lyman all American scope had a problem with elevation and windage adjustments. I called, and the lady there said to...