Search:

Might have something to do with the extended delivery schedule that NOE has now. Or maybe its just useless trivia? At any rate I'm guessing its a part time job or side interest.

Pat Marlins flux, haven't had the need to try anything else. Works great and smells great.

About 150 strokes a minute, 400 ton stamping force. The machines themselves arent that large. I'm used to operating 150 ton DACI can presses that run 155 strokes but with 11 and 14 lanes of cans...

Sometime this year there was a gent in the S&W forums who had starline make a run of 41 special brass, properly headstamped and all. He had quite a few pieces at the time, if any of you are...

370 Federal? Or do you mean the 370 sako? The 370 Sako was introduced by Federal and is based off of the new 9.3x66mm round from europe...little bit longer, somewhat short neck which gives it...

Visit here for the Model 19 Forcing cone cracking article

I recently had a 235 grain 40 cal mold cut to use in a 10mm magnum revolver. I recieved it in 10 days....yeah it was a bit of a shocker when a guy is expecting it to show up in a couple months or...

Depends on what the store is selling as "paint thinner". Mineral spirits is a petro based product typically used for thinning oil based paints. Naphtha, Mineral Spirits, Acetone, Xylene, Turpentine,...

My main concern would be making sure the bullet you're looking at is feeds reliably in a semi auto. Other than that all the normal rules apply.

Heres a bit of info that was given to me by hamilton bowen with regards to barrel gap. I had to inquire about possibly fixing mine up when I get ready to ship it out to him for a perfected bisley...

Got mine today!

Starline is generally very good brass for all pistol calibers. Starline says directly on their website they test their 45 colt brass to pressure levels of the 44 mag so you should be okay to load to...

Might have more to do with where he lives. Gets cold enough you just might need a magnum primer for reliable ignition, even with powders other than H110/296.

See the casting equipment section. There was talk of IR thermometers being used there. The big problem most ran into is the cheaper models didnt have an adjustment for sensitivity/reflectiveness of...

I've had several experiences with custom gunsmiths, good and bad. My bad was a m-14. I was told a couple months for a M-14 rifle to be assembled. Took closer to a year n half. Finally he passed...

Most of the tire shops in my town have a contract arrangement with the battery companies (Interstate I think is the one getting them all). None of them want to give any up.

If it is metaloy or metalife plating its a hard chrome plating. Plating thickness typically runs .0002-.0006 but can be as thick as .001. They usually try to stay pretty thin as hard chrome starts...

You can head over to www.mountainmolds.com and check out his opinion on various types of material he uses. He prefers brass when casting a certain range of bullet weight and with wheel weights (no...

No offense taken and non meant to you with this reply. Its easy to say that when you inherit something rather than having to pay the high cost of used or the even higher cost of new. A new 6 gang...

MP-Molds

A member here who does custom molds/group buys. You can currently buy the HG 68 in a 6 gang aluminum mold from his website. I purchased one last week. Great alternative to trying to...

http://www.theantimonyman.com/ladles.htm

Put me down for a 4C military ball.

http://www.nsksales.com/ for your 200 SWC. If you need a lot they are running a special orders of 2000.

Missouri bullet is also good.

http://www.keadbullets.com have some bullets from them,...

CMMG is a big player in the Ar market. They do manufacture their lowers for sure, maybe uppers too and sell them to other companies...I hesitate to say smaller companies because rock river doesnt...

You got it. In fact if you visit lee's website they pretty much tell you its the same just less the "accessories".