Yeah, not worth melting down due to the lead in it......... ;P
Dan
Type: Posts; User: 220swiftfn
Forum: Lead and Lead Alloys
Yeah, not worth melting down due to the lead in it......... ;P
Dan
Forum: Lead and Lead Alloys
With this many pages, it's hard to remember what's made it in here...... Has a "Jacobite" hallmark been listed??
Dan
Forum: Cast Boolits
Dillon SDB's use proprietary dies that don't even have threads...
They're also a four station press, so seat and crimp are already separate operations..
As someone else already mentioned, the...
Forum: Cast Boolits
Well, Hornady 7th has data for lead 124gr with Power Pistol, starting with 4.3gr for 900fps and a max load of 5.7gr for 1100fps. They don't have a lead load listed for 115, but I'm pretty sure that...
Forum: Cast Boolits
Just as an aside for future reference, you can't tell if a powder charge is light, heavy, or even missing by weighing the loaded round. Weight variances of the components themselves are more than...
Forum: Cast Boolits
Well, this is your first lesson in loading 101..... Look in the case for a powder charge before you seat the projectile. Really easy with the 550B, that hole in the center of the die plate is the...
Forum: Lead and Lead Alloys
A heavy salt solution works well too, floating what you don't want. But then you have wet, so has to go into a cold pot...
Dan
Forum: Cast Boolits
What gets me about this is the OP's thought that this could prevent a squib load, which is exactly the opposite of what would happen. Squibs happen due to failing to see a non-existant SMALL charge...
Forum: Cast Boolits
Not to kick you when you're down, but do a search for "blown up guns", and you'll see why this getting the reactions it is (keep in mind that those pics are of what has happened with KNOWN powder,...
Forum: Cast Boolits
To answer your question, you can get antimony already in the mix by using clip-on wheelweights, or by using shot alloy (IIRC, chilled is 3%, magnum is 4%....)
HOWEVER, your intended use is the Lee...
Forum: Reloading Equipment
As stated above, you could use the funnel/expander from the 38/357 for your 9mm (it's a thou bigger, and I *think* there's enough adjustment in the powder die to make it work as is. If not, shorten...
Forum: Lead and Lead Alloys
Well, I looked, and the trick with melting points is all about where the temp stalls (the transitions). If you had a stall at 580 as the remaining solid turned liquid, there's a strong possibility...
Forum: Lead and Lead Alloys
Hang on a sec...... Had to remember that it was Matweb that I saw all this stuff on (I think they have the melting points....)
Dan
Forum: Cast Boolits
Um, huh??? There's a nut and bolt on the handle guide that can be adjusted to limit the flow on the Pro-Melt. Agree with the mold temp, with an addition of the mold needing a good scrubbing...
As someone else already mentioned, a call to EGW with your measurements will probably get you to where you want to be for the lowest reasonable cost. Barrel to bushing and bushing to slide fit are...
Forum: Casting Equipment
I ran into one of those fat RCBS sizers too..... spinning it on some emery cloth will take it down to fit without too much trouble...
Dan
Forum: Boolit Lube !
THere was a formula that I followed that was by volume, I just used a canning jar as the "double" part of the boiler (they have the fluid oz. molded into the side, close enough for me....)
Just...
Forum: Casting Equipment
Assuming that you're talking about a bullet sizing die, yes, the Lee push-through will work with ANY standard thread press (it's 7/8"-14).
OTHER sizing dies only work with "lubri-sizers", but...
Forum: Cast Boolits
Then again, with SAAMI specs of 14,000psi in a case designed around the bulk of black powder, you're not going to get in trouble with book loads......
Now if you're loading "Ruger only" loads,...
Forum: Our Town
Or there's always VO-5 or Bag Balm........
Once again, not really a recipe, but they work.......
Dan
There's a web site that has dimensional drawings of both styles...... I'll see if I can find it again.......
http://www.tmtpages.com/web_images/pages/R.C.B.S.%20Mold%2038-150-KT%20%20159_gr.htm...
Forum: Cast Boolits
Selling a gun for a profit is perfectly legal...... They DO have a grey area as to when you are selling enough guns to warrant it being "a substantial portion of your income"....... Weasle wording...
Forum: Leverguns
Filing the shell stop on the carrier MAY be needed, but I'd suggest making sure that the guides are set right first.... There's a little slop in the mount screws, and sometimes you can get long...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |