I have used 'copper' wire wheels from China to clean dies and other machined parts/tools.
The 'copper' wheels are really brass and not brass coated steel and can be used on a bench grinder.
I have...
Type: Posts; User: kywoodwrkr
Forum: Reloading Equipment
I have used 'copper' wire wheels from China to clean dies and other machined parts/tools.
The 'copper' wheels are really brass and not brass coated steel and can be used on a bench grinder.
I have...
Forum: Military Rifles
Before you grind on shell holder, is there enough space between bottom of case and shell holder to insert a .010 feeler gauge or feeler stock?
A lot of shell holders have different rim depth space...
Forum: Completed Deals
Thanks one and all.
Cylinder has gone to a higher calling.
Going to use it in shop project.
thanks
Forum: Completed Deals
smorin2,
Molds arrived today.
The 6 cavity will go into the shop with me for a hair cut.
Have a thicker steel sprue plate as well for the 2 cavity.
Thank You!
Best of luck in your endeavors.
Forum: Completed Deals
Sir,
Have enough pull down 7,65x53 to fill a SFRB.
Just pulled two from the pile and they have HS FAMMAP 1942 & 1943.
Have the pulled bullets from them as well.
Have some stripper clips from...
Forum: Completed Deals
Finally got home and can measure cylinder, sorry for the delay.
Vernier caliper value is 1.730.
Will try to verify tomorrow morning with CMM.
Will also do mouth of chambers if time allows.
thanks...
Forum: Completed Deals
Ratchet Diameter is from two measurements(4 points ea):
.6118 and .6119
Rear pin hole diameter is .2520
Front pin hole diameter is .2529
Front boss diameter is .4326
Forum: Completed Deals
Additional pictures added and additional commentary.
thanks
Forum: Completed Deals
Thanks for clarification question.
Typically OM chamber length .357 are in range of 1.60-1.62.
NM in 1.64 to 1.65.
Overall length OM 1.860, NM 2.000
addendum: OM 357 Cylinder Dia 1.67, NM 357...
Forum: Completed Deals
Would like to sell a Ruger Blackhawk 357 cylinder I consider to be in good condition for $125 shipped in US.
Payment methods:Check(held for clearance), USPS MO and PayPal F/F.
Feel free to ask...
Forum: Completed Deals
I'll Take this, PM to follow,
Lee 44-200 mold, Beagle attempt (messy plates) casts well, switched to NOE mold to replace, $20.
thanks
Mold arrived.
Bought for a friends Ruger, then found a TC...
Forum: Reloading Equipment
I am trying to get a new appearing Herters N72 shotgun reloading press in operation.
Have some basic information on the press so not in complete dark.
The documentation, like me, seems to wander...
Forum: Reloading Equipment
I had a full auto MAC 10 in 9mm that might have liked this die.
Can't test theory on it now as it went hunting pirates in the Caribbean.
Forum: Vintage Reloading Gear
You might note it has an adapter to 7/8-14 dies.
Someone more knowledgeable about this might explain what can also be used with this press, ie. shot-shells dies etc.
Started using Herters equipment...
In earlier days I had a J2.5 atop a Remington 513S.
Now they just lounge in a drawer awaiting proper attachment.
Liked the long eye relief on it plus the light gathering under a canopy of trees....
Please add my name those in thanks to Michael.
Have a friend I'm trying to teach to reload and Michael provided me with a Lee loading kit at real reasonable cost.
The Lee loader was used in...
Forum: Completed Deals
Have an extra Dillon 550 shellplate #5 to trade for either of Dillon 550 #8, D, or U.
I send my shellplate postpaid to you, you send your shellplate postpaid to me.
thanks
Forum: Completed Deals
Back to top for a few days.
A thank you to those who visited my WTT.
Forum: Completed Deals
Want to trade extra 357 cylinder for a 9mm cylinder.
Cylinder shows very little to no wear.
Length of Cylinder 1.957 TL
Ratchet Height .150 Height
Front Ring .165 Height
Cylinder 1.733 Dia
If...
Forum: Completed Deals
5 - Lyman U311316 Hollow Point 1 cavity New $45
I'll take above mold.
PM to follow.
thanks
Forum: Completed Deals
I'll take this:
Mauser Bolt Rifles
Ludwig Olson
3rd Edition
Hardback
$25 + $5 shipping
PM inbound.
Forum: Completed Deals
Are you sure you don't want an E?
This link https://dilloncdn.com/magento/charts/rl450-rl550-conversion-chart.pdf
shows 2 sheelplates 7 and E!
2007 550 Document contains:
Shellplate E Locator...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |