Thanks all
Type: Posts; User: Chief
Forum: Reloading Equipment
I find that 32 WCF dies are available for sale at normal prices on some of the sites where I purchase reloading gear. I also notice that there are many options from the Lee set at about 40 bucks to...
Forum: Completed Deals
I have around 10 pounds of clean and sized brass looks to be mostly Speer brand, cleaned and sized ready to load along with about 350 165gr cast and powder coated flat nosed bullets to move down the...
Forum: Our Town
it looks like outside agitators trying to start trouble, at this time they don't get far
Forum: Reloading Equipment
I have a question for somebody that may have taken apart 22lr rounds. I have a brick of really old non collectable 22lr ammo that I am going to take apart and reload...reload to quiet, around the...
Forum: Our Town
Call and leave a message, on the other hand in the last couple of years I have sent him a couple of lever guns and had them back from him within the week, packaged in my original packaging...he did...
Forum: Leverguns
The screw turned out to be 10-36...the tap for it is a specialty tap for something I couldn't figure out from anybody(it was too costly) so I ordered a new screw from Marbles that is 10-32 and have...
Forum: Leverguns
I need to drill and tap a hole in the tang to mount Marbles tang sight and need to know the screw size and thread. It looks like an 8-36 screw but I don't have the tap to check it with. thanks for...
Forum: Leverguns
We shoot the targets at 50yds to 200yds and I have 3 loads that I like to use for this depending on what components I have on hand at the time. 10.5 Herco/185gr SAECO cast bullet, 15.5 2400/same...
Forum: Our Town
Tom W, you can relax now, its working fine
Forum: Reloading Equipment
Absolutely, I load both 375 and 38-55 with RCBS 375Win dies that I purchased about 1980. The .375 Win is slightly longer and slightly larger diameter(thicker brass) so crimping may be an issue, but...
Forum: Completed Deals
It is a JES rebore with 3 grooves. has no issues with leading, tho I used light loads under 1500fps mostly. I think I had it done about a year and a half ago. If I find the receipt I will know for...
Forum: Completed Deals
Of the 100 or so rounds fired from this carbine not an appreciable amount of of lead has been left in the bore, that was after 50 rounds on a hot day. It cleaned easily with the old Hoppe's #9...
Forum: Completed Deals
I didn't slug but the note I got said the bore was .375 and I shout lead at .377. The note also said to use the short version the
38-55 brass. .375 Winchester brass loaded properly to the gun is...
Forum: Completed Deals
This happens to be a made in 1970 Winchester 94 that was bored to 38-55 by the gentleman in Oregon. This started out as a 30-30 truck gun for the ranch and got bucked around a lot and even tho it...
Forum: Factory Rifles
217429
if this pic works here the top and center #1V rifles have mounts on the blocks. The center rifle has a setback ring on the rear. Both rifles using Ruger mediuim rings
Forum: Factory Rifles
I assume you dealt with this issue by now but the people at the Savage forum recommend a slightly larger size ball bearing. When I launched mine in the shop I had to find a new one and went with the...
Forum: Leverguns
about the same condition as the one in the previous post from Antiquearmsinc,
bore is likenew, amazing for a blackpowder rifle...
Forum: Leverguns
The one my buddy just got in 45/75 that is all there and in very good condition considering the age cost him 3500 bucks a month ago at a Cabela's store, but they are few and far apart so I don't...
Forum: Case Forming / Re-forming
I been using 18 gr of h110 with a 200 cast....operates the action just fine. I would guess that is a good place to start with the 180 and increase charge until it functions the action of the m1907...
Forum: Our Town
I bet you could talk them down about a thousand dollars on this item
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |