Search:

Unless a special throat has been cut the overall length is the same for 308 in the garand. You Can load it way longer and fit in the action but it wont chamber do to the throat

The "load" most used in NR A high power was 41.5 grns IMR 4895 under a 168 sierra MKHP. federal primer. This was a close duplication of the M852 match loading. It performed out to 600 yds very well...

Honing the action up to match with correct angles and a bright smooth finish is preferable to changing out springs, the only spring I change out is the trigger return spring. Changing the mainspring...

reason for the recall was they were running to long.Okay that looks to be a fairly standard housing fan motor, get one with the right mount and shaft size reuse the fan and weight. Im surprised how...

There should be an ID tag on it with specs. Call Graingers or Mc Master Carr with them they will guide you in the right direction. I would dry washing it out good and letting it dry then try it

Almost all of my BPCR are single shots so I dont crimp I hand seat most ammo. Bushing dies are good as you can adjust neck tension as needed. A roll or taper crimp done seperatly from seating should...

Depending on how bad they are decides how I do it. just lose a little JB weld I fill the hole with the handle in. Ive bought some used ones that were bad ( handles would rotate on tangs inserted)...

One change I made to mine is I pulled the little bottle of that catches the spent primers e clip and lid, found a piece of tygon tubing at the hardware store that fit the tube and put that on the...

My only complaint with my 650s was the small size of the spent primer cup ands its dropping primers on the floor as it filled up quickly. I drilled a hole thru the bottom and made a little derilin...

Start with a load of 2f powder no airspace no compression and a card wad in to .020-.040 thickness range. with the bullet seated to depth. work up from here adding compression and weight as you go....

A lot of the fix will depend on how bad the housing is? The length of the threads, How far they go in to the housing? The pitch of the threads? and last how much "room there is to work with. Im not...

Was lucky at campbells they had 2 lift trucks ( forklift for heavy coils ratted at 25,000 lbs. ( coils were 20,000 - 22,000) most machines could be moved with these. But a couple still had to be...

Last lift at Campbells was a chiller that was placed on the roof with a helicopter. They cleared the building while the lift was being done. Was interesting to watch they figured fuel consumption...

He should get an infraction for that.... Not casting sacrilege

Toe jacks and a few others beat pry bars all too.My machines range from 300 lbs up to 7500 lbs dont move them often but occasionally need to make more room.
Dad and I moved a few sheds and dead...

I thought last years would be a little bigger than this but you are probably right.With those little legs it was a chore traveling the 75-80 yds from the ditch across the road to where they are now....

Ive used the track style and they were good but for my hobby shop these do what I need and not cost a couple thousand dollars.

If you grout in the saw cuts or cracks these are good. Or even a...

Measure it out today and if I think its needed I can add a 3rd axle and 4 more wheels on each skate.

325841

Machine skates Im working on drilled the bodies and swivel plates for the pins welded pins in cleaned up faces and fitted today. Still have to cut in the flat bearing races between plates...

We had a shop here the owner built up was all big machines his brag was we can do what few others could. His band saw blades were 1 1/2" thick. Arrogant and self centered no one could be around...

Venting will be important. As will temps. fill from heavy end to light so the added weight helps force the material in. A lot of moulds in industry settings are pressure cast with a shot tube. This...

I believe the same process could be used on most presses to convert. A round plate to fit the shell holder cut and a 1 1/4"12 threaded replacement bushing for the top or 7/8 14 for the top, on some...

Today was another little one enjoying the rain was a little smaller than yesterday. Not sure how many eggs they lay in a group. Or what the average to hatch are.

I have done it in a croc pot, I wrap the fats / trimmings in cheese cloth add water and cook down. The clean fat will float let cool and it can be lifted off and dried. The cheese cloth holds the...

Wait till one that size wants to climb in the canoe with you. :(