I know this is an old thread. But, this is an issue that I dealt with multiple times over the years. And, back in 2018 found what, for me, is the perfect trail gun for the woods and waters of...
Type: Posts; User: Southern Shooter
I know this is an old thread. But, this is an issue that I dealt with multiple times over the years. And, back in 2018 found what, for me, is the perfect trail gun for the woods and waters of...
Forum: Cast Boolits
Yes, it is a SWC. But, so is the Keith design. And, as is the Speer LSCW. But, the loadings are quite different from each other.(see Alliant's page)
It is my understanding that the Speer boolit...
Forum: Cast Boolits
I cast the Lee TL240-430-SWC using wheel weights and mixed-recycled boolit lead. 99% of the time I am using Alliant Powders like Unique and Power Pistol. I am puzzled, though. The boolit design is...
Forum: Hunting with CB's
Actually, it was a statement. Using a max load of Power Pistol 880s fps was the average velocity in these guns. But, I found that 850 fps produced a tighter group, a more accurate point of impact,...
Forum: Hunting with CB's
Richhodg66, with that load the Bulldog is certainly NOT a range gun. But, shooting it enough to stay proficient and then mainly carrying it, the discomfort is short-lived.
Forum: Hunting with CB's
Landy88, that is exactly where I am heading with this. My other woods guns weigh 20-24 ounces more. One would think that I should just accept the heavier weight...and, I do while in the upper Rocky...
Forum: Hunting with CB's
I have several stoutly built .45 caliber and .44 (.430) caliber revolvers that I have carried for years while walking and 4-wheeling in the woods. But, over the years I have begun to long for...
Forum: Cast Boolits
OK. I will check out the seating depth. Thank you.
Forum: Cast Boolits
I have been shooting an HSM 250 grain cast RNFP slug on top of 9.5 grains of BE-86 from my 1989 S&W 625 in .45 Colt. Shoots great with no signs of pressure issues.
I recently landed some...
Forum: Cast Boolits
I have two .45 caliber cast boolits. One, is a traditional 250 grain round nose flat point design. The other, is a Laser-Cast 255 SWC.
Which one has the most surface bearing area?
Thank...
Just an FYI:
Recently, I loaded up some .45 Colt. 250 gr cast RNFP (HSM 250 grain hardcast) on top of 9.5 gr Alliant BE-86. It is quite accurate through my revolver. Today, I fired a short string...
Forum: Cast Boolits
8.5 gr of Unique and a 250 gr boolit is no slouch, huh?
Forum: Cast Boolits
So, 9.5 gr of Unique under a 250 gr cast boolit is at or below the 14,000 psi mark?
Forum: Cast Boolits
184587
I am a bit confused. The Alliant Powder page shows 9.5 grains of Unique as the max charge for both the 200 gr SWC and the 250 gr SWC. Is there an error, here?
Are these max charges...
Forum: Factory & Surplus Powder
Thank ya'll for the input.
Would it change anything if the boolit was more specifically the Lee 452-200-RF versus their 200 grain SWC?
Forum: Factory & Surplus Powder
On the Alliant Powder website it gives the following load:
.45 Colt
8.3 gr. Green Dot
CCI 300 primer
200 grain SWC
5.5" barrel
Is this load at or under 14,000 PSI?
Thank you.
Forum: Cast Boolits
True. I do need to check the groove size. I have not do so, yet. Thanks.
Forum: Cast Boolits
Thank you everybody. The powder coating might be a possibility to try. Guess it would increase the diameter some. My brother does powder coating. But, even if I don't do the powder coating it...
Forum: Cast Boolits
I have a Ruger Blackhawk Flattop .44 Magnum. The cylinder throats are measuring for .430 bullets. I have a lot of 500 hard cast SWC that only measure .429, though. I hate not to use these boolits....
Forum: Factory & Surplus Powder
Is 9.5 grains of BE-86 under a 250 grain cast RNFP boolit too much pressure for my .45 Colt S&W 625?
I am currently without a chrono. And, I am looking for someone who may have a solid estimation of the velocity this load may produce from my S&W 625 .45 Colt. It has a 4" barrel.
9 grains BE-86...
Forum: Factory & Surplus Powder
In reference to .45 Colt loads, I have read that a 270ish grain cast boolit on top of 12.5 grains of Blue Dot is considered a standard pressure load. One article in particular was written by Brian...
Forum: Factory & Surplus Powder
Why is it that large pistol Winchester primers are labeled for standard and magnum...the same primer...while CCI and other companies have two different primers...one for the standard primers and one...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |