Recently picked up a Chinese Mod 54 Tokarev pistol and want to start casting for it. This will be primarily a range toy as I have no intensions to use it for anything else. The barrel slugged at .312...
Type: Posts; User: Metrobluing
Forum: Cast Boolits
Recently picked up a Chinese Mod 54 Tokarev pistol and want to start casting for it. This will be primarily a range toy as I have no intensions to use it for anything else. The barrel slugged at .312...
Thanks everyone for the info. Some great starting points. Now to get busy casting and coating.
Looking to knock the newness off a NOE 358 135 FN no GC mould for some 9mm. Have a good supply of Red Dot for this load out just need some decent starting data. Anything from plinkers to “general...
Forum: Gunsmithing Tips & Tricks
I just happen to have a Mini 14 in 300aac , so I went and checked what bushing was in the gas block. I will say that the gas port in the barrel is .120 and the bushing is .065. I run mostly supers so...
Forum: Swaging
You can draw 9mm brass to make decent jackets for 308 bullets up to 165 grain.
Forum: Cast Boolits
I would start with the .429 die and polish it out till you get the desired diameter of bullet. Polish and test size as you go. Sure it's time consuming but well worth the effort.
Forum: Cast Boolits
The Lee sizer is plenty strong enough for jacketed bullets. I have found that spring back is around .002. Hope this helps
Forum: Swaging
Perhaps a slightly longer punch is needed instead of an extension. Back the die out and use a longer punch that will put you in a decent leverage spot. I make them all the time.
Forum: Gunsmithing Tips & Tricks
Have you ever considered Brownells Dicropan IM hot water bluing chemical? Hot water bluing is simple to do and has an awesome finish. Great for refinishing a pistol.
Forum: Swaging
You certainly didn`t disappoint with that solution.
Forum: Swaging
There are companies that do this for a living. I’m going to suggest he look into that first. I do however appreciate the suggestions. All would probably work.
Forum: Swaging
I was recently asked by a friend of mine who knows I swage ,what are the possibilities of using some of his father’s ashes to make some projectiles with. He wants to take pops shooting one last...
Forum: Gunsmithing Tips & Tricks
Try Brownells Dicropan IM hot water bluing. Very simple to use and the finish is awesome.
Forum: Cast Boolits
Ok, how about half jackets. Lube those also?
Forum: Cast Boolits
I mainly do swaged boolits but have recently got into casting and have a question. If I gas check the boolits made , do they need to be lubed also?
Forum: Case Forming / Re-forming
I have made hundreds of pieces out of 06 brass. Started out by cutting off the shoulder and expanding the mouth enough to ream it out with a .452 neck reamer. 30-06 brass is amazingly thick. This...
Forum: Cast Boolits
1680 works great for supersonic boolits. I have a pet load for 150 gr SP that chrony at 2000 fps without signs of excessive pressures. Main load I use in the mini 14.
Forum: Cast Boolits
Made some 500 grain RN boolits using 45 acp brass as the jacket for the .510 Whisper.
247641
Forum: Cast Boolits
Loaded a few M33 ball in .510 Whisper to do some plinking .245756
Forum: Reloading Equipment
Lately I have been running the wet tumbled brass thru an annealing machine. I will shake off the excess water first then the machine does the rest. Two birds, one stone.
Forum: Gunsmithing Tips & Tricks
Have you ever considered Cerakote? This ceramic based paint is extremely durable, resistant to just about any chemical and is DIY friendly.
Forum: Swaging
Thank you Midnight that certainly gives me a much clearer picture on what I need to make this work. Fabricating punches is a non-issue, because I own a lathe and know how to use it. It’s like with...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |