Search:

I find it strange the pins wont rinse clean ...
Are you rinising them out of the barrel or in the barrel ?
Look carefully at the inside of the rubber lining ... you should be able to see if the...

I like my cast boolits slightly heavy ... use the Lee C309-170-F in 30-30 and since I have it ... load it in my 30-06 and in my 7.5 Swiss K11 Schmidt-Ruben - 1911 Carbine (not the K31)...
and that...

That is exactly what I was thinking ... The computer programing Nerd who "revised" the data center must have no idea what handloading and reloading is ... OR
Make it so bad they have to buy our...

:goodpost:
LIKE LIKE LIKE !!!
Truer words were never spoken
Gary

CH4D also makes shell holder adapters ... I got two presses back in service with their adapters .
I don't know any other source for Universal Rams or shell holder adapters but CH4D ... you might...

50 + years casting Boolits ... and the Danged Lunchables are going to do me in !
Gary

Nothing will be gained from lubing powder coated boolits .
Just load them powder coated ... and ignore the Belt and Suspenders must be better ... Cookie Bunch .
Gary

Congratulations !!!

Sometimes a new Doctor , a fresh set of eyes and fresh idea's are all that is needed to make a huge difference !
I'm so glad you found her and she was able to help you ......

Here is the data listed in the RCBS Cast Bullet Manual .
357 Magnum - RCBS 38-158-SWC GC - sized .358"
Tested in Ruger Security Six with 6" bbl. length
Speer 357 Mag. cases - CCI #550 Magnum...

Prayer's Sent .
Have Faith ... the Good Lord will watch over and protect you .
God Bless and Keep You Always .
Gary

:goodpost:
Like Like Like !!!

That's great to hear ... I had just discovered TiteGroup a few years ago and ...
I like It !
Gary

:goodpost:
Like Like Like !!!
Gary

The plastic tends to form a "Static-Cling" that attracts the powder ... that's why the anti-static cling dryer sheets work ...
Several methods of fighting the problem work ... I think rubbing the...

For a Quickie Clean ... pull a bore snake with a little bore solvent / CLP soaked in , through the barrel ... that way you don't risk damage from a metal rod .
I can't put away any rifle without...

Ford SD ,
Hang on to that 8 X 57 chambering .
As a dedicated cast boolit shooter , a 175 gr or 190 gr. cast boolit ...
Over 13 grs. Red Dot , makes for a real sweet shooter .
Don't fear the...

:goodpost:
LIKE LIKE LIKE

Accuracy beats SD seven ways to Sunday .
Gary

I now make it a habit when ordering a NOE boolit mould to get a proper NOE
(M- type ) expander plug to go with that NOE boolit ... the little inserts are not that expensive and take up hardly any...

That bullet (Lee 358-166-SWC) in 38 special case , was most accurate with either 3.0 grains of TiteGroup ...
or with 3.0 grains of Bullseye @ abot 800 fps . Not a bad boolit , but my mould was a...

You need to get it mounted ...
A nice shoulder mount would look good on the wall ...
But you have to stop with the "Heel Stomp" ...
That drives the Taxidermists insane ... all the extra work !...

In the state of Louisiana , cap and ball guns , revolvers and rifles are not considered "firearms". I recently ordered an 1863 Police Pocket Colt revolver reproduction from IMA - USA and it was...

Rule #1 - Never pass up a good excuse to buy another boolit mould .

I need / would like to try a boolit with a crimp groove ...(great Excuse)
427666 is a nice looking Round Flat nose ... perfect...

Triggerhappy243 ... I mix Lithi-Bee like this :
I use a Crock Pot and stiff Wire whisk . Put the beeswax and grease in the crock pot on High . Have the lid and fire extinguisher at hand in case...

This is the only mix that I know of .
1 part Lucas Red-N-Tacky Lithium Grease /
3 parts Beeswax . Never any leading in any of my handguns or 30-30 rifle with Lithi-Bee ... using it since 1978...

:goodpost:
LIKE LIKE LIKE !!!
Gary

Lyman used to sell a 450 handle upgrade / conversion kit .
It has all the parts to convert the old stamped parts to the Round Ball handle like the 4500 . I bought a complete kit a couple years ago...