I've posted before regarding this press, but am still "on-the-fence," regarding same. I've been reloading off, and on, for 45 years...all on RCBS & Lyman single-stage presses. I like the auto-index...
Type: Posts; User: jlh
Forum: Reloading Equipment
I've posted before regarding this press, but am still "on-the-fence," regarding same. I've been reloading off, and on, for 45 years...all on RCBS & Lyman single-stage presses. I like the auto-index...
Forum: Reloading Equipment
gphido.....Thanks for your reply.....One last question.....If you have RCBS dies, do those dies, with their round, knurled lock-rings, fit on your turret heads without a problem?.....I'm not fond of...
Forum: Reloading Equipment
gpidaho......My thoughts, exactly....With a progressive, one is "out" a fortune, for all the caliber-conversions, if one loads multiple calibers....'With a turret, its a simple matter of switching...
Forum: Reloading Equipment
I have been considering these three presses. I currently have an RCBS turret-press, but am looking for something that will speed things up a bit, without going to the headaches, costs, and...
Forum: Reloading Equipment
I am looking for input on the Lee Classic Turret Press, and am considering the purchase of one. Is there sufficient space on the turret-heads for other makers' dies?...The Lee lock-rings are...
Forum: Reloading Equipment
'For those who own one, how do you like it?...Is it possible to still prime on the press without using the priming-system, just dropping the primer into the priming-cup, by hand?...I was considering...
Forum: Reloading Equipment
Has anyone every used one of these for a portable, reloading-bench...I have one and have been thinking of mounting a press to it, for portability. I'm in a limited-space situation. Any alternate...
Forum: Cast Boolits
Is Missouri Bullet still "good to go?"......If not, who do you recommend?
Thanks
Forum: Coatings and Alternatives
I'm getting ready to order some of these in 40 S&W for shooting in a Glock 35. I don't have an aftermarket barrel. What is the difference between these, and plated bullets like Berry's? What would...
Forum: Reloading Equipment
I received my bulge buster, today, that I had ordered earlier in the week. Tomorrow, I plan to prep some once-fired, 10mm brass for reloading. Should I run them through my RCBS sizer first, and see...
Forum: Reloading Equipment
Has anyone used one of these for handgun? It will check multiple calibers, and is "priced-right," over individual, conventional, max-length case gauges. Price is around $30, while individual case...
Forum: Reloading Equipment
Thanks, JohnB in Glencoe. It appears that the Lee FCD/Bulge Buster combo, is half-the-price of the Redding carbide. I assume the both work equally, as well. I know that the Lee offers more...
Forum: Reloading Equipment
I have acquired a large quantity of once-fired, 10mm brass, that I plan to reload. I'm sure the majority has been shot through Glocks, which is what I plan to do, but with with an aftermarket...
Forum: Reloading Equipment
I haven't bought dies (primarily RCBS/Lyman) in many years, and was greatly surprised to see how much prices have increased in the interim. I am now looking at Lee Carbide Pistol Dies. I am...
Forum: Reloading Equipment
I haven't bought dies (primarily RCBS/Lyman) in many years, and was greatly surprised to see how much prices have increased in the interim. I am now looking at Lee Carbide Pistol Dies. I am...
Forum: Cast Boolits
Thanks, RoadBike, as well as all other responders. The LCP is what I would be loading for.
I appreciate everyone's input.
Forum: Cast Boolits
I'm getting ready to order some Missouri Bullet .380, 95 gr. projectiles. Does anyone have any experience with this particular bullet. They show to be .356 in dia. Has anyone found that these need...
Forum: Cast Boolits
I plan to load Missouri Bullet Co. 180 gr bullets, 18 BHN in my 10mm. I have looked for load data, but am unable to find it. Would it be acceptable to use the data for 180 gr FMJ, of the same...
Forum: Reloading Equipment
Has anyone used the RCBS Uniflow, with the "large" cylinder, designed for rifle powder, for dispensing small volumes of pistol powder, i.e. Unique, Bullseye, etc? I recently acquired a used Uniflow,...
Forum: Cast Boolits
I have cast pistol bullets in the past, using straight, wheel-weights, and Lee molds, but am not as experienced as most here......I just place the wheel-weights straight into my Lee Production Pot,...
Forum: CB Loads / Military Rifles
I plan to load for this rifle. What is the process for forming brass from 30.06, and what steps are involved? Since jacketed bullets are nonexistent at this time, I would like to shoot cast, at...
Forum: Cast Boolits
Does anyone know a good supplier, who has any inventory?
Thanks in advance.
Forum: Leverguns
Is the Missouri Bullet 165 gr. projectile suitable for use in a Marlin 336, being sized at .309? Is it necessary to use gas-checks for a 1200 fps plinking load, if I should elect to use a Lee mold...
Forum: Leverguns
Has anyone had any dealings with this Searcy, Arkansas-based company? I am considering purchasing some once-fired brass from them and know nothing about them. Thanks in advance.
What is a good lube for lubing the sprue-bushing, locator-pins and v-blocks on Lee molds? I do not have any of the bullet-lube, which Lee recommends. I only have liquid-alox and the mold...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |