Exactly my thinking
Type: Posts; User: jimr
Forum: Factory Rifles
has any one had any luck with this particular rifle shooting cast? i have been trying the Lee 200 gr. 7 Lyman 311672 . the best i have been able to get with either bullet is about 1&1/2in. @ 100yds....
using that same bullet & powder load i found by adding a dacron filler my groups were much tighter and about 2ins. higher then without.
is that a proven load or a one time group, just curious ....
it seems like after about 40 or so rds my groups start to open up. i'm shooting lyman's 311672 wd-ww's sized to .310 in a FN-SPR-A1A .308 over 32.0 of IMR4895 with dacron filler with a c.o.l.of...
Forum: Cast Boolits
+or - .5grain works well with all my rifle bullets . i don't weigh pistol bullets.
Forum: Cast Boolits
i believe all cast bullets have a air pocket hidden in there. i know when i cut a cast pure lead round ball in half with a razor you'll see it in the first or second cut,always there.
Forum: Cast Boolits
i have had very good results with IMR4831
i would say it's the lead.
i the past 3 months i have shot almost 1000 rds out of a garand and not a bit of leading. lyman mold#311672 , ww water droped sized to .310, gc, nra 50-50 lube, imr4895,...
Forum: CB Loads / Military Rifles
the use of dacron helped control the stringing in my groups.
Forum: Special Projects
i built this rifle in 1975. it is built on a KRAG action turned into a single shot, fited with a douglas 1&1/4 to 1 in. barrel, with a 12x unitrel in a walnut and maple lamatited thumb hole stock...
Forum: Special Projects
i am thinking of making a neck sizer die for my 22-30/30 ackley imp. i would like my necks to end up with an O.D. of .245.
my question it should i ream the neck are to .245 or should ream a...
Forum: Reloading Equipment
i started with this bullet run out thing a couple of years ago with high hopes of elimiting the flier. i realy thought i was on to something till a couple of days ago. i was shooting my heavy weigth...
Forum: CB Loads / Military Rifles
i would say yes, if the garand is in good shooting order.
Forum: Cast Boolits
i seatled on 36grs. of imr4895, no filler, & lyman #311672 with gas check & lube weigh about168grs. sized to .310 with .300 nose, cycles the action quiet well and holds about 2ins. @100yds. about...
Forum: Cast Boolits
that is a general seating depth an does not mean your rifle will accept it. load 1 round without powder an primer to see if it will work.
better yet take a fired case an size it to where it...
Forum: CB Loads / Military Rifles
MtGun44,,, you beat me to the gun on your post about the micrometer.
Forum: CB Loads / Military Rifles
you can get the action to function proper with several powders, but,,,,, if you want decent accuracy try imr 4831.
also try some bullets by not lubbing all the groves. i tried this on my bullet i...
Forum: CB Loads / Military Rifles
i see in you previous post in this thread that this is not the first time this has happened to you. i would change your filler to dacron. you would think that it would be blown out the barrel. when i...
Forum: Cast Boolits
if i size(w. d. rifle bullets) just after casting i have a chance to or will kind of crush or slightly swell up the nose a bit as to where it will not chamber . the nose of the bullet will hang up in...
with that same load of 2400 with a cast 165gr bullet ,my 1917 stock eddystone loves it also.open sights 100yds 2ins. or less.
Ben, good shooting an a dam nice rifle
jim
Forum: CB Loads / Military Rifles
haven't got a chance to use the range today,but my filler on this run of test in the garand has been dacron, i have 10 each loaded with 39 & 40 grs. with & without filler. will post the resluts...
Forum: CB Loads / Military Rifles
as i stated earlier i was going to take the velocity in the garand a little higher then the 1900fps. that i been shooting, 33.5grs. of imr4895. well i started going up 1gr. at a time. it is...
Forum: CB Loads / Military Rifles
my experiance with T P over powder in the 30-06 is after the shot i noticed a few feet in front of the muzzle i would see a small white cloud of white dust. i can't imagine how your T P is staying...
Forum: Cast Boolits
and you paid money for that, wanna buy some more.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |