agreed...my Hatch/Wyman automated master caster sits on a 24" deep bench with the control unit to the right...total width is about 12" for the MC and 12" for the control...to its left is the...
Type: Posts; User: wymanwinn
Forum: The Star Equipment Corner
agreed...my Hatch/Wyman automated master caster sits on a 24" deep bench with the control unit to the right...total width is about 12" for the MC and 12" for the control...to its left is the...
Forum: The Star Equipment Corner
in the Hatch/Wyman design, the hand lever is retained to make it easier to operate the Master Caster in what i call the "warm up stage"...that is proofing the mold and running a couple of throws to...
Forum: The Star Equipment Corner
what are the part numbers to the new air cylinder and the new valve...might just think about this a bit...
thanks Hatch!
Forum: The Star Equipment Corner
UPDATE
thought i would chime in here and give an update to the Hatch/Wyman automated Master Caster
as seen in post #1 of this thread Hatch automated my version of the air assisted Master...
Forum: The Star Equipment Corner
i get 720/hr and has Hatch says, one can "multi-task"....i lube and size at the same time....
Forum: The Star Equipment Corner
never got the email....sorry...:(
Forum: The Star Equipment Corner
i am still subscribing to the original Hatch automated MC....keep it simple i say...LOL...
i rather enjoy being out in my Cave (reloading room) tending to the MC busy purring away making about 720...
Forum: Casting Equipment
thanks, i know i have been kinda absent....but i still lurk around...LOL
:drinks:
Forum: Casting Equipment
Tazza,
i run my Hatch/Wyman MC at 725F and the cycle is about 10 seconds...pour, 2sec hold, drop and hold for about 4 and return....the fan is wide open...never had your problem...my sprue plates...
Forum: The Star Equipment Corner
what exactly are you looking for size wise.....i have lots of .750 thick CPVC floating around....
Forum: The Star Equipment Corner
PM sent, please reply via email...
wyman
Forum: Cast Boolits
it may be a couple of weeks before the Moose Mould 516375 shows and the .514 expander arrived yesterday....made a "dummy' copper bullet in .516 today at work...will full length size, expand the neck...
Forum: The Star Equipment Corner
4.5" sounds about right....you just want to adjust so the arm gets a full stroke up and down...may need some fiddling....i can measure for sure when i get home...
wyman
Forum: Cast Boolits
done this rodeo......500 compression die on the way.....:)
:)
Forum: Cast Boolits
it appears that, after a lengthy conversation with Brandon at Buffalo Arms, Cimarron has remove all info regarding the "bore" size and twist rate from their website....AND that Brandon recalls that...
Forum: Cast Boolits
My Uberti 1876 Winchester Centennial Story
In early 2013 I had a hankering for a new rifle and the Uberti 1876 Centenial, 28”bbl in .50-95 caught my eye at Buffalo Arms….i got in touch and by...
Forum: Cast Boolits
ordered!!!
really appreciate all the help ndnchf!!!
looking forward to getting this round on paper.....:)
wyman
Forum: Cast Boolits
update...
did some more measuring and figuring....i know, dangerous...LOL
first, slugged my barrel....measured .5140-.5145"...NOT .510" as advertised
my CH4D neck expander measured as...
Forum: Cast Boolits
now, that's my idea of a big lube bullet......
thanks!!!!
Forum: Cast Boolits
thanks Dubber....my thoughts as well....
Forum: Cast Boolits
not so much worried about the bullet "backing out" but rather the bullet being pushed further into the case while the rounds are in the mag tube....
thanks for the response Kevin...
wyman
Forum: Cast Boolits
ndnchf,
received my Lyman 515139 today.....no crimp groove...where do you roll crimp to that bullet....?
thanks again for your help!!!
wyman
Forum: The Star Equipment Corner
don't have a clue Howard....depends on your actual compressor output in CFM and the number of strokes of your sizer cylinder per minute....
that said, my compressor is an 60 gallon vertical with a...
Forum: Cast Boolits
i ordered the Lyman and saw your post on CasCity....78gr of 3f under the Lyman....cant wait....do you use a card wad on top of the powder?
thanks again...
wyman
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |