As the title states, I am looking for some 38-55 brass. Preferably Starline. Long or short.
Thank you!
Type: Posts; User: Two Barrels
Forum: Completed Deals
As the title states, I am looking for some 38-55 brass. Preferably Starline. Long or short.
Thank you!
Forum: GB RUN BY 2 dogs
Please add me to the list for (1) brass mold, 3 cavity, PBHP.
js DOT graham at mindspring DOT com
Thanks!
Forum: Completed Deals
I am looking for some new 32-20 brass. Starline is preferred. Please send a PM if you have any to sell.
Thanks,
Scott
Forum: Completed Deals
I’ll take the rest for $190 shipped. PM on the way.
I have one of the M&P 340s. It is slightly heavier due to the steel cylinder vs titanium. It has never seen a 357 round but has seen plenty of 38 special loads. It usually is loaded with either...
Forum: Group Buy Archives
Mine were delivered today. They shipped on 3/20.
Forum: Group Buy Archives
I would like (1) 4 cavity PB mold with all pins, brass, .432”, js dot graham at mindspring dot com
Thanks,
Two Barrels
I had loaded up several different loads in 32 S&W Long, 32 H&R, and even 38 Super using Rem 1-1/2 SPP. Yesterday I noticed many of these primers in the 32 loads were pierced. The 32 S&W Long loads...
Hodgdon lists a few 2-1/2” loads in their data on their website. The 16 Ga Forum that bdicki posted a link to is a place you should visit. The issue with these shorter shells is not so much...
Forum: Reloading Equipment
Start with a single stage. As long as it is a quality press, you will always have it and find a use for it even if you step up to a progressive press later. Even old used RCBS and Lyman presses...
Forum: Cast Boolits
Interesting read. I have always used CCI and Winchester primers, but not Federal. That is mainly due to off the shelf availability where I live. The article states these are similar in costs to...
Forum: Completed Deals
I’ll take one box. PM headed your way.
Forum: Cast Boolits
I use IMR most often for rifles. I have gravitated towards Hodgdon for most shotgun loads. For revolver and pistol loads I have yet to settle on one manufacturer.
I like Boyt soft cases. The older ones were made in USA. The newer ones I believe are imported from China unfortunately.
I own a 40 S&W. It was the first pistol I ever bought. I have no use for it since discovering 1911s. I cant’t even trade it away unless I am willing to tape a $100 bill to it.
Forum: Rimfire Area
Looks really nice and the scope compliments the rifle well. Post up a range report once you get to shoot it.
My 5” Kimber will feed everthing I have tried in it. For SWC, I use a commercially produced H&G 68 clone. The COL I use is 1.240” with a taper crimp of .470”.
Forum: Cast Boolits
Loaded three different loadings of 300 H&H to test out along with a handful of 7mm-08. Might get to the range on Sunday afternoon.
Forum: Reloading Equipment
This thread gave me an idea. I load 327 Federal and 32 H&R. Those dies did not come with a spacer. I think I will set my dies up for 32 H&R and use the spacer from my 44 Special/44 Mag die set to...
Forum: Reloading Equipment
I have been using a MEC 600JR for decades. Still works.
Forum: Completed Deals
I would like all 4 remaining boxes. PM incoming.
Forum: Lead and Lead Alloys
I hope this works out for you. Looking forward to some pictures.
Forum: Group Buy Archives
1 box of 5 handles please. 29640
js dot graham at mindspring dot com
Two Barrels
Thanks!
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |