Buddy..
Will 6 foot 5 get it done...? :-)
In all seriousness, i appreciate your response to my ad but I really am looking for a blued model.
Thanks...
Type: Posts; User: shadowcaster
Forum: Completed Deals
Buddy..
Will 6 foot 5 get it done...? :-)
In all seriousness, i appreciate your response to my ad but I really am looking for a blued model.
Thanks...
Forum: Completed Deals
I am looking for a Ruger Vaquero in 45 Colt. It Must be the early large frame model, 5.5 inch barrel, blued, in very good condition. Any help would be appreciated in locating this item.
Thanks...
Forum: Completed Deals
Does anyone have any Sharpshooter molds they would like to sell?
Forum: Completed Deals
Thank you but they only carry Lee and are out of stock. I am really looking for the Sharpshooter mold in .310 caliber.
Forum: Completed Deals
Wanting to buy a .310 cal Sharpshooter buckshot mold in excellent condition. I would also consider purchasing other caliber Sharpshooter molds.
Thanks...
I know it's been a year since your post.. any updates, sucesses, failures?
Also, you stated that you got 1300 fps with published data.. is that data for a standard 2 3/4 length shell which you then...
Forum: Casting Equipment
Here is a link to the bottom pour pot I designed and built.
http://castboolits.gunloads.com/showthread.php?146065-New-bottom-pour-smelting-pot!
Shad
Forum: Casting Equipment
You don't run into any of those problems when using a "Shad Style" Bottom pour Spout and pot.
Most of those valves have plastic or teflon in them.. It won't work
Shad
Forum: Casting Equipment
If you have to be ready to catch over flow due to problems.. Then I think there is a flaw in the design.
Shad
Forum: Casting Equipment
Even with a bottom pour pot (I built a 400 pounder) you are still going to have skim and flux. I found that a metal ice fishing ladle for clearing the ice works excellent. My ladle has 1/4 inch...
Wow.. nice work! Using hot water is a big plus in the cooling dept. The fact that the ramp is below the water line amazes me. How far below? The shot must stay soft/hot enough to roll down the...
Forum: Muzzleloading.
+1
14$ a pound.. Where? I would buy 10 pounds if at that price.
I have not tried pellets so I can't say, but for me, I find the best use for BP substitutes is in a break open shotgun. Load'm...
Forum: Muzzleloading.
Generally WW's are a bit too hard for maxi balls. Try something softer closer to pure lead. WW's do work well for patched round balls though.
Shad
Forum: Casting Equipment
Cast iron Corn wedge pans stack the same.. 1 in then 1 out, and come in at just over 2 pounds each.
Shad
Forum: Casting Equipment
Regular muffin tins are a pain.. Not my idea of a good time. I'll chime in with the others on using cast iron, they fall out every time with no muss, no fuss.
Shad
Forum: Lead and Lead Alloys
I agree here.. Very seldom do I have to add anything to my range scrap. If I do it is a very small amount for long skinny boolits.
Shad
Forum: Casting Equipment
166 degrees F is not a very big window, and if not paying attention, going over happens quickly.
Shad
Forum: Casting Equipment
You can control the temp of any pot/melt with an attentive eye and a thermometer.
Shad
Forum: Lead and Lead Alloys
I couldn't have said it better myself! :)
Shad
Forum: Casting Equipment
It sounds like a lot of work and could be a safety hazard if not done correctly. I run 2 Lee pro 4-20's side by side. Fill them both with ingots and help one of them heat up with a propane torch...
Forum: Casting Equipment
When it comes to smelting/rendering scrap lead, especially in large batches... a propane burner, a thermometer, and a large cast iron or heavy welded steel pot is really hard to beat. The...
Forum: Casting Equipment
If you use only 1 pot, make sure you clean it very thoroughly between every smelting and casting session. If not, you will end up with dirt and junk in your boolits.
Shad
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |