Search:

Buffalo Arms has a custom Lyman/RCBS sizing die in .319 for 48.00 on their web site.

Similar to what Outpost said but I made a casting of my Victory cylinder throats using Creosafe. I use NOE Mk1 38/200 mold and size to .364.

I did something very similar to what 17nut did. I got a second 450 from ebay to use with soft lube and after receiving it I found the ram had a lot of play between it and the housing. This play made...

I also have one of the original steel handles that I got 3 years ago. I like them so much that I haven't use my Lyman or Lee handles since then. The reason I got them was because my hand and grip...

I use NOE when I can but they don't do custom sizes. Buffalo Arms has a much larger inventory of lyman m-die expander plugs that will fit in the M1 and M2 bodies. If he is out of stock on the size I...

GunFun,
The wiring diagram is on the motor label. The two yellow wires connect to the capacitor with blue & brown as line voltage & green for ground, Bruce.

I don't if this will work for pistols but it what I use for rifles. This is the link "www.gun-shots.net/wp-content/uploads/measuringoveralllength.pdf".

Guys, I agree with what straightshooter1 said about the use of fillers, not only with Red Dot, but with any fast burning shotgun/pistol powders. Larry Gibson has a sticky in the "CB Loads, Your...

I agree with what everyone has said above. I also neck size my 303 case with the Lee Collet die and while I have both the Lyman 31 M-Die and the Lee Universal Case Mouth Expander it is the Lee flair...

Guys, I'm going to agree with what lownbow said. I have two #4's that shoot, one is a 5 groove that measures .3025 bore & .314 throat and the other is a 2 groove that measures .304 bore & .315...

Like bangerjim I got a big bag of it at Wal-Mart.

I use to size .001 over land and .002 over groove but I ran into a problem with one of my #4 Enfield's that didn't hit a 100 yard target very well, so now for a bore riding boolit I size to no more...

Using hardball it drops 306 x 316.

For neck sizing I use mica. For full length sizing I use a spray mixture of alcohol and lanolin.

Had to look this one up. "Handloader's Manual of Cartridge Conversions" the best solution is: ".280 Flanged (BELL) Cut case to 1.5". Build rim up to .08" thick. Anneal case and form in form die. Trim...

The way I check a cartridge over all length is from this link. http://www.surplusrifle.com/shooting/oal/index.asp

My Lee Challenger press wasn't up to the job of brass conversion and finally broke. After reading up from guys on the forum here I replaced it with the Redding Big Boss press and I've had no problems...

I use the Lyman universal. I got it twenty or so years ago with both the hand and power cutters for it. For what I use it for they work great but I don't reload any pistol just rifle cases. So like...

I just replace the o-ring between the plug and the body. You can get them at any hardware store.

Right at the moment I'm using 40.4 grs of H4350 using a 195 grain gc bullet. The muzzle velocity is about 2000 fps.

Wow! Words fail me. I just don't know want to say.

The Crossroads of the West gun show we had in mid-december a guy was selling for 350 to 400 for what I would say was poor to fair Jap 7.7 Arisakas. When the show returns in march I think I'm going to...

Like Chicken Thief I also use QuickLoad.

Bruce

I would suggest you slug your barrel. With my 1917 30-06 Remington after I did this the bore and groove measured .302x.312. What I use for this rifle is Accurate Mold's 314299 that drops a 199 gr...

For my Turk ATF Mauser I ask Tom over at Accurate Molds if he could make a mold using the spec's of .313 bore x .328 groove using his catalog drawing of 31-180S. He did but had to increase the radus...