Search:

Geez, I jut got a couple of old Star's that I'd like to have overhauled just to be certain they are good to go, guess I am out of luck eh? I'll just have to give them a try!

I'm sure I have both of the dies you need. Drop me an email while I check my spares.

Dang, I thought I posted on this thread when I first saw it and was checking today to see if I had been any help only to find I never posted at all! The 310 set screw is a 8-32 and I've bought these...

Was Lyman marking all CMR dies as CMR from the first or is it possible to find CMR dies that still have the number code? I often don't have brass to try out in the sets I have. I really rab=n...

Thanks a bunch!

Is the thread of the plug larger than standard? Is the expander chamber marked for .35 Rem or as a special?

I just went through a group of my 310 dies trying to make them all complete, came close but as aways, needing a few small items to be correct. I have a bunch of trade material if you have any of...

Hey guys, darn I miss Floodgate! What a loss he was to us 310 wanna be champions! Does anyone have a complete and correct .35 Remington 310 set? I'm trying to piece one together and the manual...

D'0h! sorry, 310

I'm looking for a .323 expander for 8x57, I have several sizes to offer in trade if anyone has one they will part with. I'd actually prefer a .324 or a fat .323, I'm not sure Lyman actually made a...

I have a few extra universal decapping dies, I'd be interested in finding other uses for them.

I have this in a DC mould and I know this is a huge longshot but I'm looking for the zinc washers this design requires. This was a Harvey design that cast a zinc washer around the mid-section of...

I measure them at 6 11/16 X 2 1/16 X 1 10/16.
Most excellant suggestion, I have a couple of candidates already. Typical of my constrained linear thinking, not considering similar instead of exact...

There really isn't a subforum for this subject but I have a feeling us 310-nuts just also might haqve some insight into this arcane area! Has anyone found a source for boxes like the CCI brand APS...

I'm looking for a Garand barrel in 6.5 X 55 Swede, Criterion made a few a while back and I'm hoping to find one that is still in the wild. Of course I guess if someone has a built Garand so...

Title pretty much says it all, I have a couple of Hakims's that I'd like to start loading for and am looking for suggested boolit loads.

Thanks!

TNsailerman, thank you sir! I knew it was at least a close fit on .30-06, glad to hear it is a useful size! They are asking $15 on ebay just for shellholders! I'll hang onto it until it breaks!

Remember the old Lee one primer at a time priming tool that used the screw-in shell holders? I just found one in my junk, it has a type "F" shell holder in it. Anyone have a chart or remember what...

I knew Walt Melander when he had a gun shop in El Paso TX in the 1960's,is he still around? Unlikely I suppose as he was older than me then and I'm 80.

Heck, back in those days Lyman would make just about anything you asked for so I'm sure there are some .266 sizers around but probably not many! I even remember back in the '60's you could write...

I've encountered this often and it has made me about bald from tearing my hair out! I can only assume that standards were loosely followed in those days! It goes also for the seating screws and the...

Robert, thanks for the quick reply. I also can share your question about CMR dies but I am about 90 percent sure they are also intended for the hand tool unless they also have the expander button on...

I've recently encountered 310 CMR dies in calibers .264 Mag, 6.5 Rem mag and 7 mm Mag. I have never seen these calibers listed in a Lyman table showing the adapter ring and priming tool size but I...

JR was a treasure and gone waay too soon!

[QUOTE=Malamute;5435020]Looking for a complete set of 44-40 310 dies with handles.

Also would like any of the 44-40 dies individually, particularly the expander.

Have a complete 8mm mauser...