Search:

back to the top

Like the title say looking for a Parker-Hale PH 7 or 7a. I know its a longshot but just perhaps a member has one in thier parts bin or knows where i could find one.

Thanks
Mike

Thanks for all the replies. I have been looking around the net and i have found out a few things about this receiver. it seem like it was a greener shotgun once. looks like there are a few remains of...

This is the sight on a greener martini that was converted to 444. I would like to try something different for a rear sight. I bought the rifle on this site from a fellow named Tunnel. The rifle has a...

http://www.wisnersinc.com/part-catelog/
no bolt but some internals there

284689
.368 and 193grs coated with alox/jpw. I have 120 on hand at the moment. comes from a Accurate 37-193 mold
will this work for you?
Michael

I'll look after supper and see how many i might have,193 gr 20:1 if I recall correctly.
michael

I have been using Alox and 45/45/10 lube for years. The one thing I don't like about it is that the Alox lubed bullets seem to attract dust and lint. I just tried something a few days ago. After the...

2 scopes left with lower price.

I don't have paypal. US postal money order or cash. Check is ok if you don't mind shipping until after it clears.
if the above is ok with you send it to address in PM

Lot 1 lower priceSpoken for
UTG 4x32 Mil dot lighted reticule scope
Ruger 4x air gun scope might have been mounted but never shot.
AR-Stoner one piece scope mount
50.00 takes it all
276188
...

Last week I built a handicap ramp for a fellow that dropped a tree on his wife( she is pretty banged up but recovering from a broken leg hip and shoulder). I did not charge him because he is a good...

I know its a longshot but id anyone has one in the parts bin please let me know. they are bot in stock at Numrich arms but i thought i would take a shot here first.
Michael

pretty sure i have an extra i will look in the morning. will let you know
Michael

256955256956

Maybe close to 200 i did not count them.
405 grains and i think pure lead. some have green bar paper and some plain old blue line loose leaf paper. lubed with Rooster..457 is what i...

I might have some i could send you. i'll look sometime this morning and let you know what i have.
Michael

sending a PM

I bought a lee push through in .314 and used a split rod with emery paper and a pistol drill to make mine. did not take long and works well.
good luck

I too have a 9.3x57r but mine has a .365 bore. I bough a 37-193 B (drops at .366)mold that was designed for the 9.3x72r but it works well in may 33.
I have tried a 14g load of Trailboss (using the...

Tim
If you are loading projectiles that are .365 then they should work. That's what i use. I cut about a half inch off the base so i could use them on the 57 mm cases and i am able to load both...

Buffalo Arms shows CH4D 9.3x72R (360) in stock. It is what i bought to modify for my 9.3x57r

Yesterday i annealed all 80 of my Federal cases dried them out and re-tumbled them. This morning i ran them through the FL sizer die and checked each one in the chamber on my rifle. They all...

I did make a trip to the hardware store
4mm is to small and 5mm is to big.
The existing screw fits into a 10-32 nut but is loose, a 10-32 screw will cross thread in the hole on the bottom of the...

I have a M33 rolling block and the installed sights are pretty poor. so I was able to buy from a member here a Lyman peep that matches the finish and is the correct height. Now to mount it.
The tang...

So i did some tinkering this morning.
Measured all my #2 shell holder and they are all within a half thousandth.
Took a thousands and a half off one with the mandrel and sandpaper trick. No joy....