I shot bullets in different diameters from 0.313 to 0.315 in 0.0005 increments the 0.315 were accurate and did not lead up the barrel. I bought a set of sizing dies in 0.001" increments to get a die...
Type: Posts; User: Pistol Champ
Forum: Swaging
I shot bullets in different diameters from 0.313 to 0.315 in 0.0005 increments the 0.315 were accurate and did not lead up the barrel. I bought a set of sizing dies in 0.001" increments to get a die...
Forum: Swaging
I shoot a Pardini HP in 32acp with a swaged 64 gr SWC that is 0.315" diameter and lubed with 45/45/10. I have no leading problems and great accuracy. I size my cases (custom sizer) so that the ID of...
Forum: Cast Boolits
Just like most things you get what you pay for. Low cost usually gives poor results. I've watched more than a few shooters testing loads over a chronograph and when the velocity seems off they...
Forum: Reloading Equipment
Go with Bruce Williams to go over your Star. He will make it perfect for your application and can answer any and all Star questions you might have.
Forum: Cast Boolits
I have the same mold and I preheat my mold to 350 - 375. I cast at 750 degrees to keep the mold hot on cool days and closer to 700 on warm days. (I cast outside) If these are for a Pardini HP I like...
Forum: Cast Boolits
Beeser, Accurate mold 31-065H is a copy of the Hornady XTP bullet with out the hollowpoint. Send the mold to Eric at Hollow point molds and with the hollowpoint the bullet will weigh 60 gr and be a...
Forum: Our Town
I have a few young ones they line up every morning for me to give them a few pounds of sunflower seeds. I put out enough so they share with the birds.
Forum: Our Town
It is explained in his book. It is a good read.
Forum: Cast Boolits
I load 125 gr in my 475 A&M mag with a 500 gr bullet
Forum: Our Town
I load for the 32 acp with a Dillon and use this aftermarket powder slide from Unique Tech.
http://www.uniquetek.com/site/696296/product/T1267
Forum: Cast Boolits
I had to wait a long time to get my brass that I ordered, over a month, but when it arrived it was good clean brass. I did not appreciate him charging my card a month before he shipped.
Forum: Our Town
Commercial vehicles can not have firearms in them in PA. I just saw a Trooper really explain this to a truck driver at an accident.
Forum: Our Town
I use a lot of propane, heat, hot water, etc. I did not want to worry about price changes so I bought a bunch of propane stock. Every time the price goes up so does the value of my stock so it is a...
Forum: Group Buy Archives
I'm number 16 on the list and I will have to drop out of this group buy.
Forum: Cast Boolits
I have a lot of sized and lubed lead bullets that are 0.313" dia. I would like to get them bumped up to 0.314 does any one know of a simple fast way to do a large volume?
Forum: Group Buy Archives
I'd like the.314" w/set of all pins and a handle.
goszkatim at aol dot com
Forum: Cast Boolits
Can you share your information on the custom mold as it looks like you have saved me lots of time to get me where I want to go. Yes I am shooting a Pardini so I need the bigger diameter.
Forum: Cast Boolits
I am so sorry that I did not use "Boolit" I started to use it but the spell check for this site flagged it as a misspelled word so I changed it. I am surprised the word "tips" is so strange here all...
Forum: Cast Boolits
I'm looking for a mold for my 32 ACP target pistol. The pistol can shoot groups of one inch at 50 yards with non-lead tips. I'm looking for a tip that weighs about 70 grains and one that I can hollow...
Forum: Our Town
You were armed. Did you ever see how far the gas shoots out of a pump.
Dakotashooter2,
You are right, he must not be a caster.
These boxes are designed so that when they are die cut there is minimum waste. This is a very efficient, low cost to manufacture design. remenber the boxes are free. This is also uses a lot less...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |